Maintenance And Service - Bosch PMF 220 CE Notice Originale

OBJ_BUCH-2650-002.book Page 21 Monday, November 30, 2015 8:42 AM
Switching On and Off
To start the machine, push the On/Off switch 1 forward so
that the "I" is indicated on the switch.
The electronic soft starting feature limits the torque upon
switching on and increases the working life of the motor.
The constant electronic control keeps the stroke rate almost
constant under no-load or load conditions and ensures a uni-
form working performance.
To switch off the machine, push the On/Off switch 1 toward
the rear so that the "0" is indicated on the switch.
To save energy, only switch the power tool on when using it.
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the orbital stroke
rate 2, you can preselect the required orbital stroke rate, even
during operation.
The required stroke rate depends on the material and the work-
ing conditions and can be determined through practical testing.
When sawing, cutting and sanding harder materials, e.g.,
wood or metal, it is recommended to work with orbital stroke
rate "6"; for softer materials, such as plastic, orbital stroke
rate "4" is recommended.
Working Advice
 Wait until the machine has come to a standstill before
placing it down.
 Before any work on the machine itself, pull the mains
plug.
Note: Do not cover off the venting slots 3 of the machine while
working, as this reduces the working life of the machine.
While working with HCS tools make sure that the covering of
the tools is undamaged.
Operating Principle
Due to the oscillating drive the application tool/accessory
oscillates up to 20000 times per minute at 2.8°. This allows
for precise work in narrow spaces.
Work with low and uniform application
pressure, otherwise, the working perfor-
mance will decline and the application tool
can become blocked.
While working, move the machine back and
forth, so that the application tool does not
heat up excessively and become blocked.
Sawing
 Use only undamaged saw blades that are in perfect con-
dition. Bent or dull saw blades can break, negatively influ-
ence the cut, or lead to kickback.
 When sawing light building materials, observe the stat-
utory provisions and the recommendations of the ma-
terial suppliers.
 Plunge cuts may only be applied to soft materials, such
as wood, gypsum plaster boards, etc.!
Bosch Power Tools
Before sawing with HCS saw blades in wood, particle board,
building materials, etc., check these for foreign objects such
as nails, screws, or similar. If required, remove foreign ob-
jects or use BIM saw blades.
Separating
Note: When separating wall tiles take into consideration that
the application tools/accessories wear heavily when used for
longer periods of time.
Sanding
The removal rate and the sanding pattern are primarily deter-
mined by the choice of sanding sheet, the preset oscillation
rate and the applied pressure.
Only flawless sanding sheets achieve good sanding capacity
and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this increas-
es the working life of the sanding sheets.
Intensifiying the sanding pressure does not lead to an in-
crease of the sanding capacity, but to increased wear of the
machine and the sanding sheet.
For precise on-the-spot sanding of edges, corners and hard to
reach areas, it is also possible to work only with the tip or an
edge of the sanding plate.
When selectively sanding on the spot, the sanding sheet can
heat up considerably. Reduce the orbital stroke rate and the
sanding pressure, and allow the sanding sheet to cool down
regularly.
A sanding sheet that has been used for metal should not be
used for other materials.
Use only original Bosch sanding accessories.
For sanding, always connect the dust extraction.
Scraping
For scraping, select a high oscillation rate.
Work on a soft surface (e.g. wood) at a flat ange, and apply only
light pressure. Otherwise the scraper can cut into the surface.

Maintenance and Service

Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
Clean Riff application tools (accessory) regularly with a wire
brush.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
English | 21
1 609 92A 1G1 | (30.11.15)