Hoover HND 915 Mode D'emploi page 47

To start the programme, press the
selected program button again to
confirm.
The programme starts automatically, the
relevant LED will stop blinking and
remain on.
The display will show the going
programme phase and time remaining to
the end that is automatically updated
during running.
If the operations described above are
made while the door is open, the
programme will not start until the door
is closed.
"AUTOMATIC" programmes
The dishwasher is equipped with a dirt
sensor, able to analyse water murkiness
during all "AUTOMATIC" program phases
(see program list); thanks to this sensor the
washing cycle parameters are automatically
adapted to the real quantity of dirt on
dishes. Thus excellent washing results are
guaranteed while optimising water and
energy consumption.
Programme interruption
Opening the door when a program is
running is not recommended especially
during the main washing and final hot rinse
phases. However, if the door is opened
while a program is running (for example, to
add dishes) the machine stops automatically.
Close the door, without pressing any
buttons. The cycle will start from where it
left off (if it is necessary, the appliance
will make a short thermal anti-shock
programme before).
IMPORTANT
A running program can be interrupted
without opening the door by pausing
the dishwasher.
To pause, hold the running program
button down for at least 3 seconds
and release when the corresponding
LED starts blinking and the display
will show that the programme is
paused.
Simply press the program button
again to restart the cycle from where
it left off (the LED will stop blinking
and remain on).
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.
Changing a running programme
Proceed as follows to change or cancel a
running programme:
Hold down the current programme
button (with the LED on) for at least 5
seconds. All programmes LEDs will turn
on for one second. The running
programme will be cancelled and the
corresponding LED will start blinking.
The display will show that the programme
has been cancelled and, eventually, that
water drain is necessary.
At this point a new programme can be
set.
15 seconds after the programme has
been cancelled and no new settings are
made , all LEDs will switch off and the
current time will be displayed alone.
92
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser.
If necessary, top up the dispenser.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off (if
it is necessary, the appliance will make
a short thermal anti-shock programme
before).
Programme operations
Whilst running, the display shows
programme phase and time remaining to
the end of the cycle, which is automatically
updated.
Programme end
A 5 second buzzer will sound (if not muted)
3 times at 30 second intervals to signal that
the programme has ended.
Programme end will be displayed (after 5
minutes all LEDs will switch off and the
current time will be displayed alone).
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF" button or dishes can be loaded
for a new cycle.
Option buttons
IMPORTANT
All options MUST be turned on or off,
BEFORE starting the programme.
"ECO" button
The "ECO" button provides over 20% time
and energy savings by reducing the final
water heating and drying times during the
last rinse cycle.
This option is recommended for any type of
washing when perfectly dry dishes are not
needed immediately.
For better drying, leave the dishwasher
door slightly ajar to promote natural air
circulation in the dishwasher.
"POWER" button
Press this button to increase the intensity
of the chosen cycle by adding a rinse cycle
and, where applicable, increasing water
temperature during the washing phase.
The "POWER" button washes tougher stains
more vigorously, always guaranteeing
the best results.
It is recommended for very dirty dishes or
for dried-on dirt when dishes were not
washed immediately.
"1/2 FLEXI" button
To ensure that your dishwasher meets all
your requirements, the "1/2 FLEXI" option
button allows you to select:
Half Load Top Basket
HALF LOAD ON
By selecting this option
UPPER BASKET
dishes are washed in the
top basket and cutlery in
lower basket.
Half Load
HALF LOAD ON
Basket
LOWER BASKET
By selecting this option
dishes are washed in the
lower basket only.
Press the button ONCE for "HALF LOAD
ON UPPER BASKET" option, TWICE for
"HALF LOAD ON LOWER BASKET"
option.
93
Lower