Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
"PROGRAMME START"/
"PROGRAMME END" and
"DELAY START"
The "PROGRAMME START"/"PROGRAMME
END " and "DELAY START" options can
be used if you want the washing to be
ready at a later time (but within 24 hours).
IMPORTANT
After
setting
the
time
of
"PROGRAMME START"/"PROGRAMME
END"
or the time of
"DELAY
START", to start the countdown you
MUST press the selected programme
button again WITHIN 15 seconds.
Should you run out of time the
display will return to the programme
screen, and you simply have to
re-set the "PROGRAMME START" /
"PROGRAMME END " or "DELAY
START" .
Setting with "SET TIME MODE
ABSOLUTE"
("PROGRAMME START" OPTION)
Set the required programme (the
relevant LED will blink to confirm the
selection).
To
select
an
option,
press
corresponding button (the LED will turn on)
Press the "MENU" button ONCE.
Press the "POWER" button to increase
the hour and the "1/2 FLEXI" button to
increase the minutes.
Example:
if at 13:00 you wish the programme starts
at 17:30, set the start time at 17:30.
PROGR. START
S 17:30
13:00
PROGRAMME
CURRENT
START TIME
TIME
To start the countdown, press the
selected programme button again to
confirm (the relevant LED will stop
blinking and remain on and the setting
programme start time will be displayed ).
At the end of the countdown, the programme
will automatically start and the programme
phase of the selected cycle will be
displayed.
If "BLACKOUT" appears on the display,
refer to "AUTOMATIC FAULT SIGNALS"
section.
("PROGRAMME END" OPTION)
This is a very useful option to set the
time you wish the programme to end
WITHIN.
Set the required programme (the
relevant LED will blink to confirm the
selection).
To select an option, press the corresponding
button (the LED will turn on)
Press the "MENU" button TWICE.
Press the "POWER" button to increase
the hour and the "1/2 FLEXI" button to
increase the minutes.
Example:
if at 13:00 you wish the programme end
the
WITHIN 17:30, set the end time at 17:30.
PROGR. END
E 17:30
13:00
PROGRAMME
CURRENT
END TIME
IMPORTANT
When entering the "PROGRAMME
END" option, the display will show
the minimum time that you can set
the programme to end by. This time
may only be extended, as you
require.
94
To start the countdown, press the
selected programme button again to
confirm (the relevant LED will stop
blinking and remain on and the setting
programme end time will be displayed ).
At the end of the countdown, the programme
will automatically start and the programme
phase of the selected cycle will be shown
in the display.
If "BLACKOUT" appears on the display,
please see the "AUTOMATIC FAULT
SIGNALS" section.
WARNING!
"INTER@CT
MAXIMUM time necessary to end the
required programme, according to
selected options. However, during
running programme, due to some
variable parameters like loading
size
and
temperature, selection of automatic
programmes, dirtiness of dishes, the
EFFECTIVE TIME to cycle end may
be shorter than forecast. The REAL
TIME of programme end may be few
minutes earlier.
Setting with "SET TIME MODE
RELATIVE"
IMPORTANT
Choosing the "SET TIME MODE
RELATIVE" the "DELAY START"
option is available only.
TIME
("DELAY START")
Press the "MENU" button ("00h" will
appear on the display).
Press the button again to increase the
delay in hours (each time the button is
pressed the delay is increased by 1 hour
to a maximum of 23).
Example:
if at 13:00 you wish the programme to start
at 17:30, set 04h.
To start the countdown, press the
selected programme button again to
confirm (the relevant LED will stop
blinking and remain on and the start time
delay will be displayed).
3D" calculates the
At the end of the countdown, the programme
will automatically start and the programme
phase of the selected cycle will be
displayed.
mix,
incoming
water
In case of power failure, the "DELAY
START" function re-starts with the
delay time at the same value just before
the power failure.
Cancelling the "PROGRAMME START"
/"PROGRAMME END" or "DELAY
START"
If the countdown has NOT already been
activated the "PROGRAMME START"/
"PROGRAMME END" or "DELAY START
can be cancelled proceeding as follows :
Hold down the "MENU" button until the
selected programme will be displayed
again.
If the countdown has already been
activated the "PROGRAMME START"/
"PROGRAMME END" or "DELAY START
can be cancelled proceeding as follows :
Hold the selected program button down
for at least 5 seconds.
95
DELAY
START 04h
Publicité
Table des Matières
