Applications; Conformity And Approval; Safety Notes - Monacor TXA-1020 Mode D'emploi

Portable
High-Power Amplifier System
These operating instructions are intended for
users of the amplifier system (e . g . DJs, speakers
at public and private events) and do not require
any specific technical knowledge . Please read
the instructions carefully prior to operation and
keep them for later reference .
All control elements and connections de-
scribed can be found on the fold-out page 3 .

1 Applications

This active speaker system of the series TXA-
1020 is a combination of a two-way speaker
system and a class D amplifier and is especially
designed for mains-independent operation . For
power supply, the unit is equipped with two lead
gel batteries that are charged when the unit is
connected to the mains . Thus, the unit is ideally
suited for mobile PA applications, e . g . at events
and lectures .
The active speaker system is equipped
with controllable inputs for the connection of
two microphones and two audio sources with
line signal level (e . g . CD / MP3 player) as well
as with two outputs (e . g . for the connection
of another active speaker system) . Audio data
of a Bluetooth audio source (e . g . smartphone)
can be reproduced via the integrated Bluetooth
receiver . For operation with two wireless trans-
mitters, the unit includes a two-channel receiver
module (2 × 16 channels in the UHF frequency
range 863 .1 – 864 .9 MHz) . The transmitters of
the series TXA-800, for example,may be used
as wireless transmitters .
Additional equipment for model TXA-1020USB:
Audio player to replay USB storage media and
memory cards

1.1 Conformity and approval

Herewith, MONACOR INTERNATIONAL declare
that the receiver module of the unit TXA-1020
and the receiver module of the unit TXA-
1020USB comply with the directive 2014 / 53 / EU .
The EU declarations of conformity are available
on the Internet:
www .monacor .com
The receiver modules and the corresponding
transmitters are generally approved for operation
in EU and EFTA countries; they are licence-free
and require no registration.
8

2 Safety Notes

The unit corresponds to all relevant directives of
the EU and is therefore marked with
WARNING The unit uses dangerous mains
voltage . Leave servicing to skilled
personnel . Inexpert handling
may result in electric shock .
•
The unit is suitable for indoor use only . Protect
it against dripping water and splash water,
high air humidity and heat (admissible ambi-
ent temperature range 0 – 40 °C) .
•
Do not place any vessel filled with liquid on
the unit, e . g . a drinking glass .
•
Do not operate the unit and immediately dis-
connect the mains plug from the socket
1 . if the unit or the mains cable is visibly dam-
aged,
2 . if a defect might have occurred after the
unit was dropped or suffered a similar ac-
cident,
3 . if malfunctions occur .
In any case the unit must be repaired by skilled
personnel .
•
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the
plug .
•
For cleaning only use a dry, soft cloth; never
use water or chemicals .
•
No guarantee claims for the unit and no
liability for any resulting personal damage
or material damage will be accepted if the
unit is used for other purposes than originally
intended, if it is not correctly connected or
operated, or if it is not repaired in an expert
way .
If the unit is to be put out of operation
definitively, take it to a local recycling
plant for a disposal which is not harm-
ful to the environment .
3 Overview
1 Display of the 2-channel receiver module,
.
indicates the transmission channel and, by
means of a segment bar, the strength of the
radio signal received
(left: receiver unit A, right: receiver unit B)
2 Power switch and volume control, for
receiver unit A and receiver unit B of the
2-channel receiver module
3 Buttons to set the 2-channel receiver
module: chapter 7 .1
☞
4 Status indicators for the rechargeable bat-
teries
When operated with rechargeable batteries:
The respective LED indicates the charging
state of the batteries . When the LED "20 %"
starts flashing, recharge the batteries as soon
as possible .
When connected to the mains: The LEDs light
up continuously one after the other while
the batteries are being recharged . When the
batteries have been completely recharged,
the LED "FULL" will light up .
5 POWER switch of the unit, will light up
during operation
6 Tone controls: TREBLE for high frequencies
and BASS for low frequencies
7 Volume control for the input signal of the
jacks LINE IN (13)
8 Volume control for the input signal of the
jack AUX IN (15) and for the integrated
Bluetooth receiver
9 Volume control for the input signal of jack
MIC 2 (17)
10 Volume control for the input signal of jack
MIC 1 (18)
11 Control MASTER for the overall volume
12 Button VOICE PRIORITY with LED indicator
for the microphone priority function: When
the button is pressed (LED illuminated), the
volume of the other audio sources will be
substantially reduced during microphone
announcements .
13 Input LINE IN (RCA jacks) to connect an
audio source with line signal level, e . g . CD /
MP3 player
14 Outputs LINE OUT (RCA jacks) and AUX OUT
(3 .5 mm jack) to feed the mixed signal of the
audio sources used to another active speaker
system or to a recorder, for example
Note: The tone controls (6) and the control
MASTER (11) will not have any effect on the output
signals at these jacks .
15 Input AUX IN (3 .5 mm jack) to connect an
audio source with line signal level, e . g .
CD / MP3 player
16 Button to switch the Bluetooth receiver on
(keep pressed for a longer period of time) or
off (press briefly) (
Button flashes: no connection to the Blue-
tooth audio source
Button continuously illuminated: connection
to Bluetooth audio source established
17 Input MIC 2 (6 .3 mm jack) to connect a
microphone
18 Input MIC 1 (combined 6 .3 mm jack / XLR jack)
to connect a microphone
19 Mains jack for connection to a mains socket
(230 V/ 50 Hz) via the mains cable provided
20 For model TXA-1020USB:
MP3 player: ☞
chapter 7 .2)
☞
chapter 3 .1