Typical Installations - Joneca Economy Manuel D'utilisation

TYPICAL INSTALLATIONS

* Dimensions are inches
Economy
Standard
Mid-Duty
Heavy Duty
Deluxe
Premium
A
13.9 13.9
B
6.3 6.3
C
5.2 5.2
D
5.5 5.5
E
3.9 3.9
F
1.5 1.5
Batch Feed Units (not pictured)
• The 3 largest models offer a Batch Feed version.
• Built in switch activated by inserting stopper.
• No extra switch or wiring required.
• Batch Feed units add approx. 2.1"/53mm to the "A" and "B" dimension.
9. TROUBLESHOOTING
Before seeking repair or replacement, we recommend that you review the following:
LOUD NOISES: (Other than those during grinding of small bones and fruit pits): These are usually caused by accidental entry of a spoon, bottle cap or other
foreign object. To correct this, turn off electrical switch and water. After disposer has stopped, remove splash guard, remove object with long handled tongs,
and replace splash guard.
UNIT DOES NOT START: Unplug power cord or turn either the wall switch or breaker box switch to "OFF" position, depending on your model and wiring
configuration. Remove stopper and/or splash guard. Check to see if turntable will rotate freely using a wooden broom handle. If turntable rotates freely, replace
splash guard and check reset button to see if it has been tripped. Reset button is red and located on the front of the disposer. Push button in until it clicks and
remains depressed.
If reset button has not been tripped, check for shorted or broken wire connecting to disposer. Check electrical power switch, fuse box or circuit breaker. If
wiring and electrical components are intact, the unit may have internal problems that require service or replacement.
IF TURNTABLE DOES NOT ROTATE FREELY: Turn off disposer, then check for any foreign object lodged between the
turntable and grind ring. Dislodge object by rotating table with a wooden broom handle (see 9A) and remove object. If no
foreign object is present, there may be internal problems.
LEAKS: If the unit leaks at the top, it may be due to:
1. Improper seating of sink flange (gasket centering, putty or tightening).
2. Support ring not tightened properly.
3. Defective or improperly installed cushion mount.
If unit leaks at the waste elbow, leak may be due to improper tightening of elbow flange screws.
A mail in Warranty Card is not required. Proof of purchase is required! Staple receipt or proof of purchase to this manual. Tracking is handled through the serial number
affixed to the bottom of the disposer. Conveniently record your model number and serial number on the front of this manual for your records. If you need warranty service, call
10.2" /261mm
10.2'' /261mm
10.9" /279mm
11.2'' /285mm
11.2'' /285mm
11.2'' /285mm
14.6 16 16 17.3
7 7.3 7.3 7.3
7.7 8.7 8.7 8.7
5.5 5.7 5.7 5.7
3.9 3.9 3.9 3.9
1.5 1.5 1.5 1.5
Dimensions in inches
888.8JONECA and have Serial Number and Receipt available for technician.
SINGLE BOWL DOUBLE BOWL CENTER OUTLET
*approx
C
B
A
E
D
F
Warranty not transferable.
(4)
DOUBLE BOWL END OUTLET
*approx
A
354 354 372 404
B
161 161 179 185
C
132 132 195 220
D
140 140 140 144
E
100 100 100 100
F
38 38 38
Dimensions in millimeters
Joneca Corporation
4332 E. La Palma Avenue Anaheim, California 92807
Telephone: 714.993.5997 Fax: 714.993.2126
Website: www.Joneca.com
E-Mail: consumerservice@joneca.com
1-888-8JONECA
*approx
404 439
185 185
220 220
144 144
100 100
38 38 38
9A
REMOVE
SPLASH
GUARD
TURNTABLE