Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Food Waste Disposer Instruction Manual
NOTE:
IMPORTANT:
CAUTION:
Record important disposer information here
Model Number*_________________________
*Above information appears on the label affixed to bottom of the disposer. For your convenience,
write down the model and serial numbers prior to installation. Proof of purchase is required for Warranty. Staple receipt or proof of
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY
TO PERSONS. SAVE THESE INSTRUCTIONS.
WARNING – When using electrical appliances, basic
precautions should always be followed, including the
following:
1.
Read all instructions before using the appliance.
2.
To reduce the risk of injury, close supervision is necessary when an
appliance is used near children.
3.
Do not put fingers or hands into a waste disposer.
4.
Turn the power switch to the off position before attempting to clear a
jam or remove an object from the disposer.
5.
When attempting to loosen a jam in a waste disposer, use a long
wooden object such as a wooden spoon or the wooden handle of a
broom or mop.
6.
When attempting to remove objects from a waste disposer use long-
handled tongs or pliers. If the disposer is magnetically actuated, non-
magnetic tools should be used.
7.
To reduce the risk of injury by materials that may be expelled by a
waste disposer, do not put the following into a disposer: clam or oyster
shells; caustic drain cleaners or similar products; glass, china or plastic;
large whole bones; metal, such as bottle caps, tin cans, aluminum foil
or utensils; hot grease or other hot liquids; whole corn husks.
8.
When not operating a disposer, leave the stopper in place to reduce the
risk of objects falling into the disposer.
9.
DO NOT operate disposer unless splash guard is in place.
10.
For proper grounding instructions see the ELECTRICAL CONNECTION
portion of this manual.
11.
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent, or authorized person in order to avoid hazard.
12.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
13.
Children should be supervised to ensure that they do not play with the
appliance.
1. REMOVAL OF OLD UNIT
TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY.
Before starting this step, turn off electrical power at
the circuit breaker or fuse box. Unplug disposer.
If your old mount is the same type as the mount on your new disposer, just
reverse the assembly instructions found in section 3. If your new mount
system is different, follow these instructions:
A.
Use a pipe wrench to disconnect drain line where it attaches to disposer
discharge elbow (see 1A).
This Food Waste Disposer has been designed to operate on 110-120 Volt, 60 Hz
exclusively. Using any other voltage or Hz adversely affects performance.
Read all instructions thoroughly. Keep this guide for future reference.
Be sure to review SAFETY INSTRUCTIONS FIRST PERTAINING TO A RISK OF FIRE,
ELECTRICAL SHOCK OR INJURY TO PERSONS before using disposer.
purchase to this manual for easy reference. Warranty non-transferable.
Serial Number*__________________________
B.
Remove disposer from sink flange by turning mount ring to the left
clockwise (see 1B). If you are unable to turn the mount ring, tap on one
of the extensions from the ring with a hammer. Some mounting systems
have tubular extensions. Inserting a screwdriver into one tube will
provide additional leverage for turning the mount ring (see 1B). Some
disposers may require the removal or loosening of nuts from the mount
screws (see 1C). Some disposers may require the removal of a clamp.
Caution: Be sure to support the disposer while performing this
step or it may fall when the mounting ring is disconnected from
the mounting assembly.
C. To remove remaining mount system from the sink, loosen mount screws,
push mount ring up. Under it is the snap ring. Use screwdriver to pop
off ring (see 1D). Remove mount ring, protector ring and gasket from
sink flange. Some mounts will require the unscrewing of a large ring
holding the sink flange in place. Pull sink flange up through sink and
clean off old putty from sink.
IMPORTANT: This is a
good time to clean out
the trap and drain lines
by running a drain auger
or
plumber's
snake
before installing your
new disposer.
2. DISHWASHER CONNECTION
If you are utilizing a dishwasher, complete the following procedure. If
dishwasher is not to be connected go on to
section 3.
A.
Using a blunt instrument (steel punch or
wooden dowel), knock out entire plug
(see 2A). Do not use a screwdriver or
sharp instrument. (When knockout plug
falls into disposer, you may remove it or
grind it up when the disposer is used. This
will not damage the disposer in any way, but may take some time to
grind).
B.
Connect dishwasher hose (see 2B, pg.2) using hose clamp. Make sure
all plumbing connections are tight and in accordance with all plumbing
codes and ordinances. Run water and check for leaks.
(1)
1B
1A
1C
1D
2A
KNOCK
OUT PLUG
WOOD OR
METAL DOWEL
IM-TRI-JON-151
Publicité
Table des Matières
