Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4. ELECTRICAL CONNECTIONS
A.
Connect disposer to appropriate household current only.
GROUNDING INSTRUCTIONS
FOR WASTE DISPOSERS EQUIPPED WITH A GROUNDED PLUG-IN POWER CORD.
B.
This appliance must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to
reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. If the supply
cord is damaged it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard. The appliance
must be installed so that reset button is readily accessible. Removing an attached power cord or plug voids the warranty.
5. ATTACHING DISCHARGE ELBOW
A.
Connect waste elbow to the disposer (see 5A), proceed to step 6 and then connect
bottom of the elbow by tightening the slip nut (see 5B).
B.
If you are connecting to a dishwasher, return to section 2B. If not, make sure all plumbing
connections are tight and in accordance with all plumbing codes and ordinances. Run
water and check for leaks.
6. CONNECTING DISPOSER TO MOUNT ASSEMBLY
A.
Line up disposer under mounting assembly. Guide hopper projections into mount ring slots. Turn mount ring about 1/4" to right so that disposer is
temporarily supported (see 6A).
B.
Turn mount ring and disposer until disposer elbow lines up with trap (see 6B).
C.
Turn mount ring to the right (counter-clockwise) until it reaches the locking position as shown (6D). Hopper projections must be to extreme left of
mounting slots (see 6C & 6D).
D.
If mount ring is hard to turn, you may add a small amount of petroleum jelly or liquid soap to hopper projections. Run water and check for leaks.
SLOT
PROJECTION
7. OPERATING INSTRUCTIONS
The Anti-Jam Swivel Impellers make a clicking
sound as they initially swing into place. This indicates
normal operation.
A.
Remove sink stopper. Turn on a medium flow of cold water.
B.
Turn switch to ON position; your motor is turning at full speed and ready
to use.
C.
Scrape in food waste. Down the drain go table scraps, peelings, rinds,
seeds, pits, small bones and coffee grounds. To speed up food waste
disposal, cut or break up large bones, rinds and cobs. Large bones and
fibrous waste require considerable grinding time and are more easily
thrown away with other trash. Do not be alarmed that the disposer
slows down while grinding. The disposer is actually increasing torque
(grinding power) and is operating under normal conditions.
D.
Before turning disposer off, let water and disposer run for approximately
15 seconds after shredding or grinding stops. This assures that all
waste is thoroughly flushed through trap and drain.
E.
It is not recommended to use hot water while running disposer. Cold
water will keep waste and fats solid so disposer can flush away
particles.
TIPS FOR SUCCESSFUL OPERATION
A.
Be sure disposer is empty before using your dishwasher so it may
drain properly.
B.
You may want to leave the stopper in the drain when not in use to
prevent utensils and foreign objects from falling into the disposer.
6A
ELBOW
TRAP
WARNING: IMPROPER CONNECTION OF THE EQUIPMENT-GROUNDING
CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC SHOCK. CHECK WITH A
QUALIFIED ELECTRICIAN OR SERVICEMAN IF YOU ARE IN DOUBT AS TO
WHETHER THE APPLIANCE IS PROPERLY GROUNDED. DO NOT MODIFY THE
PLUG PROVIDED WITH THE APPLIANCE IF IT WILL NOT FIT THE OUTLET. HAVE
A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
6B
C.
Your disposer is ruggedly built to give you many years of trouble free
service. It will handle all normal food wastes, but it will NOT grind or
dispose of such items as plastic, tin cans, bottle caps, glass, china,
leather, cloth, rubber, string, clam and oyster shells, aluminum foil or
feathers.
8. CLEANING AND MAINTENANCE
DO NOT ATTEMPT TO LUBRICATE YOUR DISPOSER!
The motor is permanently lubricated. The disposer is self cleaning and scours
its internal parts with each use.
NEVER put lye or chemical drain cleaners into the disposer, as they cause
serious corrosion of metal parts. If used, resulting damage can be easily
detected and all warranties are void. Mineral deposits from your water can
form on the stainless steel turntable, giving the appearance of rust. DO NOT
BE ALARMED, the stainless steel turntables used will not corrode.
(3)
RUBBER
GASKET
5A
6C
LOCKING DETAIL
HOPPER PROJECTION IN
"SUPPORTED" POSITION
HOPPER PROJECTION IN
"LOCK" POSITION
5B
6D
MOUNT
RING
Publicité
Table des Matières
