Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
AIR GAP
*
RUBBER
HOSE
DISHWASHER
HOSE
DRAIN
DISPOSER
*Air gap may not be required
for all installations. Check local
plumbing codes.
SPEED MASTER MOUNT SYSTEM
STOPPER
SINK
FIBER GASKET
SUPPORT RING
(NOTE ARROWS
INDICATING UP)
GROOVE
HOPPER
RESET BUTTON
(FRONT)
DISCHARGE ELBOW
IMPORTANT NOTICE: CUSHION MOUNT DETAIL
3D
TOP OF SINK FLANGE
SINK
FIBER
GASKET
BOTTOM
BEAD OF
CUSHION
MOUNT
OPEN AREA, NO
MOUNT RING
OBSTRUCTION
SHOULD BE FREE TO
MOVE UP & DOWN
3. INSTALLATION OF MOUNTING ASSEMBLY
2B
READ COMPLETELY BEFORE STARTING
NOTE: Pay close attention to the order of mount assembly parts, as they have
been correctly assembled by the factory (see
3A). Also, reference the cushion mount detail in
illustration 3G for the proper position of the
cushion mount.
NOTE: Try practicing this assembly before you
get under the sink to get the "feel" of how the
parts fit together.
A.
Disassemble mount assembly from
disposer by turning mount ring to the left
(clockwise) and remove.
B.
Raise mount ring toward top of sink
flange. Remove cushion mount. Remove
mount ring. You may want to practice
3C
installing the cushion mount at this point
before you are under the sink. See
REMOVABLE
paragraph H. Also see the "Important
SPLASH GUARD
Notice: Cushion Mount Detail."
C.
Unscrew support ring from sink flange and remove fiber gasket. You are
SINK
now left with sink flange and rubber gasket.
FLANGE
D.
The rubber gasket is used instead of plumbers putty with stainless steel
sinks. Other sinks will require putty.
E.
If no putty is used, insert sink flange through rubber gasket into sink
RUBBER SINK
opening. Do not rotate sink flange once it is seated.
FLANGE GASKET
(OR PUTTY)
F.
If you use putty instead of the gasket, form a ring around underside of
sink flange (see 3D). Insert flange into sink opening, press down hard
to squeeze out excess putty (see 3B). From under sink, trim off excess
putty flush with bottom edge of sink opening.
G.
From underneath sink, slip fiber gasket onto exposed sink flange. With
arrows pointing up, screw support ring onto the sink flange, hand
tighten until the sink flange will not move. At this point you may want to
MOUNT RING
insert stopper in sink and fill with water to check sink flange seal and
TIGHTENING EARS
ensure there are no leaks.
CUSHION MOUNT
H.
Place mount ring over sink flange and hold in place while installing cushion
mount (large side down) so the groove on the inside of cushion mount fits
DISHWASHER
INLET
over lip on sink flange, similar to putting the lid on a plastic container (see
3E, 3F & 3G). Please read important notice below.
ELBOW GASKET
SCREWS
I.
The disposer must be installed so that the reset button is readily accessible.
ELBOW
FLANGE
3E
When the cushion mount is installed
correctly, the lip of the sink flange fits
into the groove on the inside of the
cushion mount and the mount ring can
be pulled downward over cushion
3F
RUBBER
mount and will be free to rotate. The
GASKET
bottom bead of the cushion mount acts
SUPPORT
as a gasket between the bottom of the
RING
sink flange and the top of the disposer.
See illustration 3G.
SINK
FLANGE
CUSHION MOUNT DETAIL
SUPPORT
RING
GROOVE
BOTTOM
BEAD
(2)
Speed Master Mount System
REMOVABLE SPLASH
GUARD
SINK FLANGE
SINK FLANGE
GASKET
FIBER GASKET
SUPPORT RING
MOUNT RING
3A
CUSHION MOUNT
SINK
3B
3G
MOUNT
RING
BOTTOM
"LIP" OF
SINK
FLANGE
CUSHION
MOUNT
Publicité
Table des Matières
