Conformity And Approval; Charging The Batteries - Monacor International JTS KA-10T Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

range depends on local conditions and may reach
60 m as a maximum

3.1 Conformity and approval

Herewith, MONACOR INTERNATIONAL declare that
the audio transmission system KA-10 /1PACK com-
plies with the directive 2014 / 53 / EU The EU dec-
laration of conformity is available on the Internet:
www jts-europe com
The transmission system is licence-free and gen-
erally approved for operation in EU and EFTA
countries
4

Charging the Batteries

The transmitter and the receiver are supplied with
power via a built-in rechargeable lithium-ion bat-
tery: Prior to initial operation, fully recharge the
batteries
1) Connect the power supply unit provided to
the jack "12 V 500 mA" (12) of the charger,
then connect the power supply unit to a mains
socket (230 V/ 50 Hz) The charging LEDs (14)
keep flashing as long as the charging slots (13)
are empty
2) Insert the transmitter and the receiver into the
charging slots according to fig 4 After a few
seconds, the charging LEDs light up If they fail
to light up, push the units deeper into the slots
3) When the battery of a unit has been fully re-
charged, the corresponding charging LED is
extinguished The unit can be removed from
the slot
4) After the batteries have been charged, discon-
nect the power supply unit of the charger from
the mains socket
Notes
– If a charging LED keeps flashing during the charging
process, the charger performs a self-test to protect the
batteries
– To ensure a long battery life, do not store the units with
discharged batteries If the units are not used for a longer
period, recharge the batteries every three months
– To replace the battery, the unit must be opened There-
fore, a defective battery must always be replaced by
skilled personnel A suitable replacement battery is
available: TG-3 7VB (order no 28 2460)
Never put defective batteries in the
household waste; always take them to
a special waste disposal, e g collection
container at your retailer
5
Fastening and
Connecting the Units
For a better distinction between the units, the
housing of the transmitter is black and marked
with a large T at the front; the housing of the
receiver is grey and marked with a large R
1) The transmitter and the receiver are both pro-
vided with a clip (5) This clip can be used to
fasten the units on your clothes, e g belt or
trouser pocket
Alternatively, use the supplied shoe mount
adapter (11) to screw one of the units onto a
camera support with 6 3 mm thread (¼") The
adapter can also be used to mount the receiver
on the shoe for the video light / flash unit of the
camera To hold the shoe mount adapter in
place, put it under the clip of the transmitter
or the receiver (fig 3)
2) The transmitter is equipped with a built-in mi-
crophone (9) to pick up the sound It is also
possible to connect the supplied tie clip micro-
phone to the jack MIC / LINE (1); in this case, the
built-in microphone is switched off If required,
put the supplied windshield / pop shield on the
tie clip microphone To attach the microphone,
e g to your tie, fasten the supplied clip to the
microphone cable
If the KA-10 /1PACK is used for wireless
transmission of line audio signals, connect the
audio source (CD / MP3 player, radio, mixer etc )
to the jack MIC / LINE
3) Connect the jack AF OUT (1) of the receiver to
the audio input of the camera or the following
unit (amplifier, mixer etc ) A connection cable
with two 3 5 mm plugs and an adapter cable
(3 5 mm plugs to XLR plugs) is supplied with
the system
9

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Jts ka-10rJts 25.3120Jts ka-10/1pack

Table des Matières