Bosch GSR 12V-35 Professional Notice Originale page 7

Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for driving and loosening screws
and for drilling in wood, metal, ceramic and plastic.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Keyless chuck
(2) Torque presetting ring
(3) Gear selector switch
A)
(4) Battery release button
A)
(5) Battery
(6) Rotational direction switch
(7) On/off switch
(8) Battery charge indicator
(9) "PowerLight" lamp
(10) Handle (insulated gripping surface)
A)
(11) Screwdriver bit
A)
(12) Universal bit holder
A)
(13) Belt clip
A)
(14) Bit holder
A)
(15) Colour clip
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless drill/driver
Article number
Rated voltage
A)
No-load speed
– First gear
– Second gear
Max. torque, hard/soft
screwdriving application ac-
A)
cording to ISO 5393
Max. drilling diameter (first/second gear)
– Steel
– Wood
Screw diameter max
Bosch Power Tools
Cordless drill/driver
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
– during operation
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Assembly
u
Removing the battery (see figure A)
u
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
GSR 12V-35
To remove the battery (5), press both release buttons (4)
and pull the battery downwards out of the power tool. Do
3 601 JH8 0..
not use force to do this.
V= 12
Follow the instructions on correct disposal.
Changing the tool (see figure B)
-1
min 0–460
-1
min 0–1750 The drill spindle is locked when the on/off switch (7) is not
pressed. This makes it possible to change the application
Nm 35/20
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (1) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the sleeve of the keyless chuck (1) by turning
mm 10
it by hand in the direction of rotation ➋ until it audibly clicks
mm 32
into place. This will automatically lock the drill chuck.
mm 8
A)
B)
and
during storage
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
1 609 92A 4KZ | (07.06.2019)
English | 7
GSR 12V-35
mm 0.8–10
kg 0.93 - 1.2
°C 0 to +35
°C -20 to +50
GBA 12V...
GAL 12...
GAX 18...