Publicité
Les langues disponibles
Les langues disponibles
*1 Not supplied
*2 Speaker impedance: 4 Ω to 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Power amplifier (not supplied)
*5 Subwoofer (not supplied)
*6 Depending on the type of car, use an adaptor for a
steering wheel remote control (not supplied).
For details on using the steering wheel remote control,
see "Using the steering wheel remote control" (page 13).
*7 Depending on the type of car, use an adaptor (not
supplied) if the antenna (aerial) connector does not fit.
*8 Whether in use or not, route the microphone input cord
so it does not interfere with driving operations. Secure
the cord with a clamp, etc., if it is installed around your
feet.
*9 For details on installing the microphone, see "Installing
the microphone" (page 12).
*10 For more information on how to install the SiriusXM
Connect Vehicle Tuner, consult the installation guide
supplied with the tuner.
*11 When connecting the iDataLink Maestro module (not
supplied), do not connect any device to the REMOTE IN
terminal (blue). Likewise, when connecting a device to
the REMOTE IN terminal (blue), do not connect the
iDataLink Maestro module (not supplied) to the IDATA
LINK I/F terminal (black).
*12 Use the connection cable supplied with the iDataLink
Maestro module (not supplied).
*13 Connect when using Apple CarPlay with a wireless
connection.
*14 Front speaker/Front tweeter
If [Speaker Configuration] in [Sound] is set to [Front &
Rear], connect the front speaker. If [Speaker
Configuration] in [Sound] is set to [Front 2-way], connect
the front tweeter.
*15 Rear speaker/Front woofer
If [Speaker Configuration] in [Sound] is set to [Front &
Rear], connect the rear speaker. If [Speaker
Configuration] in [Sound] is set to [Front 2-way], connect
the front woofer.
Making connections
To a common ground (earth) point
First connect the black ground (earth) lead then
connect the yellow and red power supply leads.
To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
Note
It will take about 10 seconds to shut down the output of
REM OUT after the unit is turned off.
To a car's illumination signal
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the parking brake switch lead
The mounting position of the parking brake
switch lead depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply leads to the
parking brake switch lead.
Parking brake switch lead
Hand brake type
To the +12 V power terminal of the car's rear
lamp lead (only when connecting the rear
view camera)
To a car's speed pulse signal
When using Apple CarPlay with a wireless
connection, it is necessary to connect to keep
the accurate location of your car.
The mounting position of the speed pulse
output lead depends on your car.
To an interruption signal (+3.3 V to +12 V) to
display the picture from CAMERA IN 1 and
CAMERA IN 2
Note
REVERSE IN, EXT IN 1, and EXT IN 2 interrupt detections
have the following priority levels.
REVERSE IN always has priority; if both EXT IN 1 and
EXT IN 2 occur at the same time, EXT IN 1 has higher
priority.
Foot brake type
11
EN
Publicité
