Publicité
Les langues disponibles
Les langues disponibles
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
1.5 Safety codes and standards
This appliance complies with the latest version of one or
more of the following standards:
¡ ANSI Z21.1 / CSA 1.1 Household Cooking Gas
Appliances
¡ Installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54 or, in Canada, the
Natural Gas and Propane Installation Code, CSA
B149.1.
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards
apply to specific installations.
1.6 Electrical safety
¡ Installer - show the owner the location of the circuit
breaker or fuse. Mark it for easy reference.
¡ If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
¡ Local codes vary. The installer is responsible for
ensuring that the installation, connections, and
grounding comply with all applicable codes. The
manufacturer is not responsible for any issues
associated with the improper installation of this product.
¡ The appliance must be electrically grounded in
accordance with local codes or, in the absence of local
codes, with the National Electrical Code, NFPA 70
latest edition or, in Canada, the Canadian Electric
Code, CSA C22.1-02.
¡ Be sure your appliance is properly installed and
grounded by a qualified technician. Installation,
electrical connections and grounding must comply with
all applicable codes.
¡ Do not use an extension cord.
¡ Do not use an adapter.
¡ Refer to the rating plate for more information.
→ "Rating plate location", Page 17
WARNING
Before installing, turn power OFF at the service panel.
Lock service panel to prevent power from being turned
▶
ON accidentally.
For appliances equipped with a cord and plug, do not cut
or remove the ground prong.
It must be plugged into a matching grounding type
▶
receptacle to avoid electrical shock.
If there is any doubt as to whether the wall receptacle is
▶
properly grounded, the customer should have it
checked by a qualified electrician.
GROUNDING INSTRUCTIONS
This appliance must be grounded.
▶
Grounding reduces the risk of electric shock by
▶
providing a safe pathway for electric current in the
event of a short circuit.
▶
Be sure your appliance is properly installed and
grounded by a qualified technician.
▶
Installation, electrical connections and grounding must
comply with all applicable codes.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician install an outlet near
the appliance.
Before you plug in an electrical cord, be sure all controls
are in the OFF position.
Before you turn on power supply, make sure all controls
are in the OFF position.
1.7 Gas safety
Requirements for gas supply:
¡ Install a gas shutoff valve near the appliance. It must be
easily accessible in an emergency.
¡ Leak testing must be conducted by the installer
according to the instructions in this manual.
¡ The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing at pressures in excess of ½ psi
(3.5 kPa).
¡ The appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff
valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than
½ psi (3.5 kPa).
¡ The minimum supply pressure must be 1" water column
above the manifold pressure printed on the rating label.
The maximum supply pressure must not exceed 14.0
inches water column (34.9 Millibars).
¡ A metal flex line or fixed metal pipe shall be used to
connect gas to the appliance. If a metal gas line cannot
be used, consult your local certified electrician or local
electric codes for proper grounding.
en-us
5
Publicité
