KitchenAid KTRC19KKBL00 Guide D'utilisation Et D'entretien page 19

Are the doors closed completely?
Push the doors firmly shut. If they will not shut all the way, see
"The doors will not close completely" later in this section.
Are the condenser coils dirty?
This prevents air transfer and makes the motor work harder.
Clean the condenser coils. Refer to the "Cleaning Your
Refrigerator" section.
NOTE: Your new refrigerator will run longer than your old one due
to its high efficiency motor.
The refrigerator seems to make too much noise
The sounds may be normal for your refrigerator.
Refer to the "Understanding Sounds You May Hear" section.
The ice maker is not producing ice
Is the freezer temperature cold enough to produce ice?
Wait 24 hours after hook-up for ice production. See the
"Setting the Control(s)" section.
Is the wire shut-off arm in the OFF (arm up) position?
Lower the wire shut-off arm to the ON (arm down) position.
See the "Ice Maker" section.
Is the water line shut-off valve to the refrigerator turned
on?
Turn on the water valve. See the "Connecting the Refrigerator
to a Water Source" section.
Is an ice cube jammed in the ejector arm?
Remove the ice from the ejector arm with a plastic utensil.
Refer to the "Ice Maker" section.
Does the ice maker mold have water in it or has no ice
been produced?
Check to see if your refrigerator has been connected to your
home water supply and the supply shut-off valve is turned on.
Refer to the "Connecting the Refrigerator to a Water Source"
section.
NOTE: If not due to any of the above, there may be a problem
with the water line. Call for service.
The ice maker is producing too little ice
Has the ice maker just been installed?
Wait 72 hours for full ice production to begin. Once your
refrigerator is cooled down, the ice maker should begin
producing 70-120 cubes every 24 hours.
Has a large amount of ice just been removed?
Allow 24 hours for ice maker to produce more ice.
Is the control set correctly?
Refer to the "Setting the Control(s)" section.
Is the water shut-off valve turned completely on?
Turn valve on fully. Refer to the "Connecting the Refrigerator
to a Water Source" section.
Is there a water filter installed on the refrigerator?
This filter may be clogged or installed incorrectly. First, check
the filter installation instructions to ensure that the filter was
installed correctly and is not clogged. If installation or
clogging is not a problem, call a qualified person or a
technician.
Off-taste, odor or grey color in the ice
Are the plumbing connections new, causing discolored or
off-flavored ice?
Discard the first few batches of ice.
Have the ice cubes been stored for too long?
Throw old ice away and make a new supply.
Has food in the refrigerator been wrapped properly?
Refer to the "Refrigerator Features" section.
Do the freezer and ice bin need to be cleaned?
See the "Cleaning Your Refrigerator" section.
Does the water contain minerals (such as sulfur)?
A filter may need to be installed to remove the minerals.
Is there a water filter installed on the refrigerator?
Grey or dark discoloration in ice indicates that the water
filtration system needs additional flushing. Run additional
water through the water dispenser to flush the water filtration
system more thoroughly at least 2 to 3 gallons (8 to12 liters)
or 6 to 7 minutes initially. Discard discolored ice.
The water dispenser will not operate properly
Has the water system not filled?
The water system needs to be filled the first time it is used.
Dispense 2 to 3 gallons (8 to 12 liters) of water into a large
container and discard it. Refer to the "Water Dispenser"
section.
Is the water shut-off valve not turned on or the water line
connected at the source?
Check to be sure the water shut-off valve is turned on and the
water source is connected to the refrigerator. Refer to the
"Connecting the Refrigerator to a Water Source" section for
directions.
Is the water shut-off valve clogged or incorrectly
installed?
Refer to the "Connecting the Refrigerator to a Water Source"
section. If clogging or installation is not a problem, call for
service or contact a plumber.
Is there a kink in the home water source line?
If you find or suspect a kink in the water line, call for service.
Is there a water filter installed on the refrigerator?
The filter may be clogged or incorrectly installed. First, check
the filter installation instructions to ensure that the filter was
installed correctly and is not clogged. If installation or
clogging is not a problem, call for service.
Water leaking from the dispenser
Is the glass not being held under the water dispenser long
enough, causing water to drip?
Hold the container under the water dispenser two to three
seconds after releasing the dispenser lever. Water may
continue to dispense during this time.
Is there a water filter installed on the refrigerator?
The water filtration system may have air in the lines, causing
water to drip. Additional flushing may help clear air from the
lines. Normal dispenser use should flush air from the lines
within 24 to 72 hours.
19