DeWalt DW745 Traduction De La Notice D'instructions Originale page 25

WARNING: Never use the machine without the table insert.
Immediately replace the table insert when worn or damaged.
Mounting the upper blade guard (fi g. E)
• Fasten the guard (6) to the riving knife (5) with the bolt (27).
• Place the washer (28 & 29) and wingnut (30) onto the other end of
the bolt and tighten.
Mounting and adjusting the parallel fence (fi g. A1, F1 & F2)
The rip fence (8) can be installed on the left or right side of your table
saw.
• Locate the screw (31) with the slot (32) in the rip fence.
• Secure the rip fence by snapping both latches (33) in place.
Adjusting the fence parallel to the blade
The fence has been factory-set. If you need to re-adjust, proceed as
follows:
• Set the saw blade to its highest position.
• Remove the upper blade guard (6).
• Set the bevel angle to 0°.
• Unlock the rail lock lever (13).
• Move the fence (8) until it touches the blade.
• Check that the fence is parallel to the blade.
• If adjustment is required, proceed as follows:
• Using an Allen key, loosen the adjustment screw (31) locating the
fence to the fence rail.
• Adjust the fence parallel to the blade.
• Tighten the adjustment screw.
• Lock the rail lock lever and check that the fence is parallel to the
blade.
• Be sure to replace the blade guard after the adjustment.
WARNING: If there is not enough travel in the pinion bearing
assembly, take the unit to an authorized D
agent.
Adjusting the rip scale
The rip scale reads correctly only when the fence is mounted to the right
of the blade.
• Check that the pointer (9) indicates zero on the scale when the fence
is just touching the blade. If the pointer does not indicate exactly
zero, loosen the screws (34), move the pointer to read 0 and tighten
the screws.
Bevel stop and pointer adjustment (fi g. G1 & G2)
• Set the saw blade to its highest position.
• Unlock the bevel lock lever (12) by pushing it up and to the right.
• Loosen the bevel stop screw (35).
• Place a set square (36) on the table and up against the blade (37).
• Adjust the bevel angle using the bevel lock lever (12) until the blade
is fl at against the square.
• Tighten the bevel lock lever (12).
• Turn the bevel stop cam (38) until it fi rmly contacts the bearing block.
• Check the bevel angle scale. If adjustment is required, loosen the
pointer screw (39) and set the pointer to 0°.
• Tighten the pointer screw (39).
• Repeat the procedure at 45° for the 45° bevel stop, but do not adjust
the pointer.
Adjusting the mitre fence (fi g. H)
• Install the mitre fence (19) in the slot to the left of the blade.
• Loosen the lock knob (40).
• Place a square (36) against the fence face (41) and the blade (37).
All manuals and user guides at all-guides.com
• Check that the pointer (42) indicates 90° on the scale. If the pointer
OPERATION
Instructions for use
The attention of UK users is drawn to the "woodworking machines
regulations 1974" and any subsequent amendments.
• Never place either hand in the blade area when the saw is connected
• Never use your saw for freehand cuts!
• Do not saw warped, bowed or cupped workpieces. There must be at
• Always support long workpieces to prevent kickback.
WALT repair • Do not remove any cut-offs from the blade area while the blade is
E
Switching on and off (fi g. A1)
• To switch the machine on, press the green start button.
• To switch the machine off, press the red stop button.
NOTE: Switching activity may produce short-term voltage changes or
fl uctuations. Under unfavourable conditions in public low-voltage supply
systems impairment of other appliances might appear. Disturbances will
not occur if the impedance is less than 0.262 Ohms.
Sockets used for these power tools shall be fused by a 16 Amperes
cut-out with an inert characteristic.
Basic saw cuts
• Always use the riving knife.
• Always ensure that the riving knife and blade guard are correctly
Ripping (fi g. A1 & I)
• Set the bevel angle to 0°.
• Adjust the saw blade height. The correct blade position is to have the
• Set the parallel fence to the required distance.
• Adjust the position of the L-shaped fence profi le (48) level with the
does not indicate exactly 90°, loosen the screw (43), move the
pointer to read 90° and tighten the screw.
WARNING:
• Always observe the safety instructions and applicable
regulations.
• Ensure the machine is placed to satisfy ergonomic conditions
in terms of table height and stability. The machine site shall
be chosen so that the operator has a good overview and
enough free surrounding space around the machine that
allow handling of the workpiece without any restrictions.
• Install the appropriate saw blade. Do not use excessively
worn blades. The maximum rotation speed of the tool must
not exceed that of the saw blade.
• Do not attempt to cut excessively small pieces.
• Allow the blade to cut freely. Do not force.
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles are tight.
to the electrical power source.
least one straight, smooth side to go against the rip fence or mitre
fence.
running.
aligned.
WARNING: Sharp edges.
tips of three teeth just protruding through the top surface of the wood.
Adjust the height of the upper blade guard as necessary.
back of the riving knife. When ripping wide pieces of material, slide
E N G L I S H
23