DeWalt DW650 Mode D'emploi page 22
Masquer les pouces
Voir aussi pour DW650:
- Traduction de la notice d'instructions originale (109 pages)
Publicité
Les langues disponibles
Les langues disponibles
All manuals and user guides at all-guides.com
E N G L I S H
• Before replacing the top cover of the mains plug
ensure that the cable restraint (3) is holding the
outer sheath of the cable firmly and that the two
leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor size
is 1.5 mm
2
. When using a cable reel, always unwind
the cable completely. Also refer to the table below.
2
Conductor size (mm
)
Cable rating (Amperes)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Cable length (m)
7.5
15
25
Voltage
Amperes
Cable rating (Amperes)
115
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
10
5.1 - 7.0
10
10
15
7.1 - 12.0
15
15
20
12.1 - 20.0
20
20
25
230
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10
10
10
7.1 - 12.0
15
15
15
12.1 - 20.0
20
20
20
en - 4
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Replacing and centring the sanding belt (fig. B & C)
Your Belt Sander uses 100 x 570 mm sanding belts.
• Place the tool on its side with the clamping
lever (12) upwards.
• Pull the clamping lever (12) upwards and to the
right.
• Remove the sanding belt (5).
• Place a new sanding belt making sure that the
arrow on the inside of the sanding belt points in
the same direction as the arrow on the machine
when on the same side of the rollers.
.
• Push the clamping lever back.
• Switch the machine ON and turn the outer belt
centring knob (6) until the sanding belt is centred
on the roller (11).
The sanding belt should never project at
the rear! The sanding belt should be
flush with the outer edge of the sanding
surface.
DW650E - Setting the electronic speed control
dial (fig. D)
• Turn the speed control dial (2) to the desired
position. The higher the number, the higher the
belt speed.
DW650(E)K - Mounting, removing and adjusting
the sanding frame (DE6500) (fig. A & E)
• Remove the sanding belt.
30
45
60
• Remove the front crankshaft (13) from the
sanding frame (14).
6
6
6
10
• Push the crankshaft into the semi-circular
6
6
15
15
mountings in the sander where it will be held in
15
20
20
place by the clamping spring (4).
20
20
25
• Mount the finger guard (15) to the sanding frame
25
25
-
using the screws (16) and washers (17) as shown.
-
-
-
• Mount the sanding belt as described above.
6
6
6
6
• Click the front crankshaft (13) into the clamping
6
6
6
6
spring (4).
6
6
10
15
• Rotate the knob (18) to set the rear crankshaft of
10
15
15
the sanding frame at right angles with the
15
20
20
sanding belt. Push the sanding frame onto the
20
25
-
rear crankshaft.
16
Publicité
