Christopeit Sport 1738 Notice De Montage Et D'utilisation page 21

USER MANUAL OF COMPUTER
Function of Displays:
Pulse-Display:
Shows actually heart rate data.
Speed-Display:
Shows actually speed in km/h.
Distance-Display:
Shows actually distance in KM.
Time-Display:
Shows actually time of exercising in minutes and seconds.
Calories-Display:
Shows actually calories in kcal.
Program-No. Display:
Shows actually exercise programs P1~P9.
Program-profile Display:
Shows the exercise profile of exercise programs P1~P9.
Function of keys:
Prog-key:
PROGRAM key: On the stop status, press Prog-key to select ex-
ercising speed programs P1-P9-FAT
F-key:
Select key of time-program H-1, distance program H-2 or calories
program H-3.
Start-key:
Press Start-key to start exercise program (motor starts running) .
Stop/Pause -Key:
Press Stop/Pause-key during exercise to interrupt the program
(motor stops running). Within 5 min. you can press Start-Key to
continue this exercise program or press Stop/Pause -key again
to finish this program. Pre-values can set to zero by pressing the
Stop/Pause-key.
"+"-key:
Press speed up key increase settings or motor speed.
"-"-key:
Press speed down key decrease settings or motor speed.
Quick Speed- keys 2, 5, 9 + 15km/h:
Press one of these keys and the speed changes direct into 2, 5,
9, and 15km/h.
MANUAL MODE:
How to start manual mode:
Put in the AC plug in wall power 230V~50Hz and put on the po-
wer switch (78). Put safety clip (74) onto the computer and it will
show normal manual mode.Stand your feet on both side rails. Put
the safety key at you exercise cloth and press start-key to start
with exercising. After a 3 sec. count down, the motor begin to run
slowly and you can step on the running belt and follow the speed.
Adjust the speed with "+" and "-" -keys into desired speed. If put
off the safety clip from computer at any time, the motor stop slow-
ly and the display will show „---". After put on the safety key on
computer the normal manually program will show. Press "+" or "-"
-key to adjust value of speed. Press quick speed -key to adjust
speed quickly. All values of the displays will counter up.
Setting Programs Time-Distance-Calories:
Time Program:
On the normal manual mode, press F-key, to enter time program
H-1. The time display will flash and the initial value is 30:00. Press
"+"-key or "-"-key to set value. The range is: 5:00-99:00. If set a
value the display counts up till zero and then stops running motor.
Distance-Program:
On the normal manual mode, press F-key, to enter distance pro-
gram H-2. The distance display will flash and the initial value is
1,00KM. Press "+"-key or "-"-key to set value. The range is: 1,00-
99:00KM. If set a value the display counts up till zero and then
stops running motor.
Calories-Program:
On the normal manual mode, press F-key, to enter calories pro-
gram H-3. The calories display will flash and the initial value is
500kcal. Press "+"-key or "-"-key to set value. The range is: 20-
990kcal. If set a value the display counts up till zero and then stops
running motor.
RANGE OF ALL FUNCTIONS:
INITAL
TIME(MIN:SEC) 0:00
SPEED(KM/H) 0.0
DISTANCE(KM) 0.00
PULSE(BPM) P
CALORIES(KCAL) 0
Exercise programs P1-P9:
On the normal manual mode, press Prog-key to chose one of the
exercise speed programs P1-P9. Each program is divided into 10
intervals of time and the speed changes as following program list
shows. Initial setting time is 30min, set a time for training session
and press Start to start the program. Pressing Stop to have a break
or finish earlier the program. Press speed "+" or "-"-key to adjust
speed during the program if it is to quick or slow. With next inter-
vals of time the speed level will change back to program mode.
If the program runs till end of time the motor will stop running after
the display counts down time to zero.
21
INITIAL SETTING DISPLAY
VALUE RANGE RANGE
30:00 5:00-99:00 0:00-99:59
N/A N/A 1.0-18.0
1.00 1.00-99.00 0.00-99.99
N/A N/A 50-200
500 20-990 0-999