CARLO GAVAZZI CA18 Manuel D'instructions page 28

7.2.2. SSC parameters
Parameter Name
Teach-In Select
Teach-In Result
Teach-in State
Flag SP1 TP1
TeachPoint 1 of Set point 1
Flag SP1 TP2
TeachPoint 2 of Set point 1
Flag SP2 TP1
TeachPoint 1 of Set point 2
Flag SP2 TP2
TeachPoint 2 of Set point 2
SSC1 Parameter
(Switching Signal Channel)
Set point 1 (SP1)
Set point 2 (SP2)
SSC1 Configuration
(Switching Signal Channel)
Switching Logic 1
Mode 1
Hysteresis 1
SSC2 Parameter
Set point 1 (SP1)
Set point 2 (SP2)
SSC2 Configuration
Switching Logic 2
Mode 2
Hysteresis 2
28
Rev.00 - 06.2018 | CA18/CA30 Capacitve sensors with IO-Link interface | © 2018 | CARLO GAVAZZI Industri
Index Dec
Access
(Hex)
58 (0x3A) RW 1 = Switching Signal Channel 1
59 (0x3B) -
1 (0x01) RO
2 (0x02) RO
3 (0x03) RO
4 (0x04) RO
5 (0x05) RO
60 (0x3C)
1 (0x01) R/W
2 (0x02) R/W
61 (0x3D) -
1 (0x01) R/W
2 (0x02) R/W
3 (0x03) R/W
62 (0x3E)
1 (0x01) R/W
2 (0x02) R/W
63 (0x3F)
1 (0x01) R/W
2 (0x02) R/W
3 (0x03) R/W
Default value
1 = Switching Signal Channel 1
2 = Switching Signal Channel 2
-
0 = Idle
0 = Not OK
0 = Not OK
0 = Not OK
0 = Not OK
-
1 000
10 000
-
0 = High active
1 = Single Point Mode
CA18CAF 6%
CA18CAN 15%
CA30CAF 7%
CA30CAN 10%
-
1 000
10 000
0 = High active
1 = Single Point Mode
CA18CAF 6%
CA18CAN 15%
CA30CAF 7%
CA30CAN 10%
Data range Data Type
0 = Default channel
UIntegerT
255 = All SSC
- RecordT
0 = Idle
1 =Succes
4 = Wait for command
5 = Busy
7 = Error
0 = Not OK
1 = OK
0 = Not OK
1 = OK
0 = Not OK
1 = OK
0 = Not OK
1 = OK
-
0 ... 10 000 IntegerT
0 ... 10 000 IntegerT
-
0 = High active
UIntegerT
1 = Low active
0 = Deactivated
1 = Single Point Mode
UIntegerT
2 = Window Mode
3 = Two Point Mode
1 ... 100 UIntegerT
-
0 ... 10 000 IntegerT
0 ... 10 000 IntegerT
UIntegerT
0 = High active
UIntegerT
1 = Low active
0 = Deactivated
1 = Single Point Mode
UIntegerT
2 = Window Mode
3 = Two Point Mode
1 ... 100 UIntegerT
Length
8 bit
8 bit
- -
- -
- -
- -
- -
- -
16 bit
16 bit
- -
8 bit
8 bit
16 bit
- -
16 bit
16 bit
8 bit
8 bit
8 bit
16 bit