Makita JV001G Manuel D'instructions page 6

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
L e n g t h o f s t r o k e
S t r o k e s p e r m i n u t e
B l a d e t y p e
M a x . c u t t i n g c a p a c i t i e s
O v e r a l l l e n g t h ( w i t h B L 4025)
R a t e d v o l t a g e
N e t w e i g h t
Due to our continuing program of research and development, the specifications herein are subject to change
w i t h o u t n o t i c e .
Specifications may di er from country to country.
The weight may di er depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combinations, according to EPTA-Procedure 1/
Applicable battery cartridge and charger
B a t t e r y c a r t r i d g e
C h a r g e r
Some of the battery cartridges and chargers listed above may not be available depending on your region of
r e s i d e n c e .
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
T h e t o o l i s i n t e n d e d f o r t h e s a w i n g o f w o o d , p l a s t i c a n d
m e t a l m a t e r i a l s .
Noise
T h e t y p i c a l A - w e i g h t e d n o i s e l e v e l d e t e r m i n e d a c c o r d -
ing to EN 8 1- -11:
S o u n d p r e s s u r e l e v e l ( L
S o u n d p o w e r l e v e l ( L ) : 8 dB (A)
W A
Uncertainty (K) : dB (A)
NOTE: T h e d e c l a r e d n o i s e e m i s s i o n v a l u e ( s ) h a s
been measured in accordance with a standard test
method and may be used for comparing one tool with
a n o t h e r .
NOTE: T h e d e c l a r e d n o i s e e m i s s i o n v a l u e ( s )
may also be used in a preliminary assessment of
e x p o s u r e .
W o o d
M i l d s t e e l
A l u m i n u m
) : 8 dB (A)
p A
D.C . 3 6 V - 40 V m a x
1 , are shown in the table.
BL
DC
WARNING:
W ear ear protection.
WARNING:
The noise emission during actual
use of the po er tool can di er from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
o and hen it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN
Work mode: cutting boards
Vibration emission (a
Uncertainty (K) : .5 m/s
Work mode: cutting sheet metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
6 ENGLISH
JV001G
26 m m
-1
800 - 3 , 500 m i n
B t y p e
1 3 5 m m
1 0 m m
20 m m
283 m m
2.6 - 2.9 k g
/ BL 5 / BL
RA / DC RB / DC RC
8 1- -11:
2
) : . m/s
h , B
2
2
) : .8 m/s
h , M
2