Makita JV001G Manuel D'instructions page 11

ASSEMBLY
CAUTION:
Always be sure that the tool is
s itched o and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing jig saw blade
CAUTION:
Always clean out all chips or for-
eign matter adhering to the jig saw blade and/or
blade holder. Failure to do so may cause insu cient
tightening of the jig saw blade, resulting in a serious
personal injury.
CAUTION:
Do not touch the jig saw blade or
the workpiece immediately after operation. T h e y
may be extremely hot and could burn your skin.
CAUTION:
Always secure the jig saw blade
firmly. Insu cient tightening of the jig saw blade may
cause the blade breakage or serious personal injury.
CAUTION:
W hen you remove the jig saw
blade, be careful not to hurt your fingers ith the
top of the jig saw blade or the tips of workpiece.
Before installing the jig saw blade, make sure that the
jig saw blade clamp lever is in the released position.
To install the jig saw blade, insert the jig saw blade
(teeth facing forward) into the jig saw blade holder until
it latches. The jig saw blade clamp lever moves to the
fixed position by itself and the jig saw blade is locked.
Make sure that the back edge of the jig saw blade fits
into the roller. Pull the jig saw blade lightly to make sure
that the jig saw blade does not fall o during operation.
Fig.7: 1. Jig saw blade clamp lever (fixed position)
2. Jig saw blade clamp lever (released
p o s i t i o n )
Fig.8: 1. Jig saw blade holder 2. Jig saw blade
c l a m p l e v e r ( r e l e a s e d p o s i t i o n ) 3. J i g s a w
blade 4. R o l l e r
CAUTION:
Do not open the tool opener exces-
sively, or it may cause tool damage.
To remove the jig saw blade, open the tool opener
forward as far as it will go. This allows the jig saw blade
to be released.
Fig.9: 1. Jig saw blade holder 2. T o o l o p e n e r 3. J i g
saw blade
NOTE: In case that it is di cult to remove the jig saw
blade:
T u r n t h e c u t t i n g a c t i o n c h a n g i n g l e v e r t o t h e p o s i t i o n
" III " a n d s l i g h t l y s w i t c h o n t h e t o o l s e v e r a l t i m e s s o
that the jig saw blade holder moves to the bottom.
Make sure the jig saw blade clamp lever is in the fixed
p o s i t i o n w h e n s w i t c h o n t h e t o o l .
Remove the battery cartridge from the tool before
installing or removing the jig saw blade.
NOTE: Occasionally lubricate the roller.
Hex wrench storage
W h e n n o t i n u s e , s t o r e t h e h e x w r e n c h a s s h o w n i n t h e
figure to keep it from being lost.
Fig.10: 1. B a s e 2. H e x w r e n c h
Cover plate
U s e t h e c o v e r p l a t e w h e n c u t t i n g d e c o r a t i v e v e n e e r s ,
p l a s t i c s , e t c . I t p r o t e c t s s e n s i t i v e o r d e l i c a t e s u r f a c e s
from damage. Fit it on the bottom of the tool base.
Fig.11: 1. C o v e r p l a t e 2. B a s e
Anti-splintering device
CAUTION:
The anti-splintering device cannot
be used when making bevel cuts.
F o r s p l i n t e r - f r e e c u t s , t h e a n t i - s p l i n t e r i n g d e v i c e c a n
be used. To install the anti-splintering device, move the
tool base all the way forward and fit it from the bottom
of tool base.
W h e n y o u u s e t h e c o v e r p l a t e , i n s t a l l t h e a n t i - s p l i n t e r i n g
d e v i c e o n t o t h e c o v e r p l a t e .
Fig.12: 1. B a s e 2. A n t i - s p l i n t e r i n g d e v i c e
Dust extraction
Optional accessory
T h e d u s t n o z z l e i s r e c o m m e n d e d t o p e r f o r m
c u t t i n g o p e r a t i o n s .
T o a t t a c h t h e d u s t n o z z l e o n t h e t o o l , i n s e r t t h e h o o k o f
dust nozzle into the hole in the base.
Fig.13: 1. D u s t n o z z l e 2. B a s e
T o s e c u r e t h e d u s t n o z z l e , t i g h t e n t h e c l a m p s c r e w a t
the front of the dust nozzle. The dust nozzle can be
installed on either left or right side of the base.
Fig.14: 1. C l a m p s c r e w
T h e n c o n n e c t a M a k i t a v a c u u m
n o z z l e .
Fig.15: 1. D u s t n o z z l e 2. H o s e f o r v a c u u m
OPERATION
CAUTION:
Al ays hold the base ush ith
the workpiece. Failure to do so may cause jig saw
blade breakage, resulting in a serious injury.
CAUTION:
Advance the tool very slowly when
cutting curves or scrolling. F o r c i n g t h e t o o l m a y
cause a slanted cutting surface and jig saw blade
breakage.
Turn the tool on without the jig saw blade making any
contact and wait until the jig saw blade attains full
speed. Then rest the base flat on the workpiece and
g e n t l y m o v e t h e t o o l f o r w a r d a l o n g t h e p r e v i o u s l y
m a r k e d c u t t i n g l i n e .
Fig.16: 1. C u t t i n g l i n e 2. B a s e
11 ENGLISH
c l e a n
c l e a n e r t o t h e d u s t
c l e a n e r