Publicité
Les langues disponibles
Les langues disponibles
Indicating the remaining battery
capacity
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
l i g h t u p f o r a f e w s e c o n d s .
Fig.2: 1. I n d i c a t o r l a m p s 2. Check button
Indicator lamps
Lighted
O
NOTE: D e p e n d i n g o n t h e c o n d i t i o n s o f u s e a n d t h e
ambient temperature, the indication may di er slightly
f r o m
t h e a c t u a l c a p a c i t y .
NOTE: The first (far left) indicator lamp will blink when
the battery protection system works.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts o power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions:
Overload protection
When the battery is operated in a manner that causes
it to draw an abnormally high current, the tool automat-
i c a l l y s t o p s w i t h o u t a n y i n d i c a t i o n . I n t h i s s i t u a t i o n , t u r n
the tool o and stop the application that caused the tool
to become overloaded. Then turn the tool on to restart.
Overheat protection
When the tool or battery is overheated, the tool stops
automatically and the lamp blinks. In this case, let the
tool and battery cool before turning the tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the
tool and charge the battery.
Remaining
capacity
Blinking
5
to 1
5
to 5
5
to 5
to 5
C h a r g e t h e
battery.
The battery
m a y h a v e
m a l f u n c t i o n e d .
Protections against other causes
Protection system is also designed for other causes
t h a t c o u l d d a m a g e t h e t o o l a n d a l l o w s t h e t o o l t o s t o p
a u t o m a t i c a l l y . T a k e a l l t h e f o l l o w i n g s t e p s t o c l e a r t h e
causes, when the tool has been brought to a temporary
h a l t o r s t o p i n o p e r a t i o n .
1.
Turn the tool o , and then turn it on again to
r e s t a r t .
.
Charge the battery(ies) or replace it/them with
recharged battery(ies).
.
Let the tool and battery(ies) cool down.
If no improvement can be found by restoring protection
s y s t e m , t h e n c o n t a c t y o u r l o c a l M a k i t a S e r v i c e C e n t e r .
Selecting the cutting action
This tool can be operated with an orbital or a straight
line (up and down) cutting action. The orbital cutting
action thrusts the jig saw blade forward and increases
c u t t i n g s p e e d .
Fig.3: 1. C u t t i n g a c t i o n c h a n g i n g l e v e r
T o c h a n g e t h e c u t t i n g a c t i o n , t u r n t h e c u t t i n g a c t i o n
c h a n g i n g l e v e r t o t h e d e s i r e d c u t t i n g a c t i o n p o s i t i o n .
Refer to the table to select the appropriate cutting
a c t i o n .
Position
0
I
II
III
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Press the lock switch to turn on the lamp. Press the lock
switch again to turn o the lamp.
Fig.4: 1. L o c k s w i t c h 2. L a m p
NOTICE:
W hen the tool is overheated, the lamp
blinks. Cool down the tool fully before operating
the tool again.
NOTE: Use a dry cloth to wipe the dirt o the lens of
t h e l a m p . B e c a r e f u l n o t t o s c r a t c h t h e l e n s o f l a m p , o r
i t m a y l o w e r t h e i l l u m i n a t i o n .
9 ENGLISH
Cutting action
Applications
S t r a i g h t l i n e c u t t i n g
F o r c u t t i n g m i l d
a c t i o n
s t e e l , s t a i n l e s s
s t e e l a n d p l a s t i c s .
F o r c l e a n c u t s i n
w o o d a n d p l y w o o d .
Small orbital
F o r c u t t i n g m i l d
c u t t i n g a c t i o n
s t e e l , a l u m i n u m
a n d h a r d w o o d .
Medium orbital
F o r c u t t i n g w o o d
c u t t i n g a c t i o n
a n d p l y w o o d .
F o r f a s t c u t t i n g i n
a l u m i n u m
s t e e l .
Large orbital
F o r f a s t c u t t i n g i n
c u t t i n g a c t i o n
w o o d a n d p l y w o o d .
a n d m i l d
Publicité
