Nemox Crea Série Mode D'emploi page 10

preservation cycle and run the selected
program.
Subsequently, the preservation cycles
associated to the selected program ill be
enabled.
PADDLE LOCK UPON LID OPENING
The opening of the lid (3) only stops the paddle
(5) and does not affect the preservation cycle.
The closure of the lid (3) enables the paddle
operation (5) (on the condition that it is provided
by the selected preservation cycle in that
moment). If the mixture proves excessively hard
and prevents the movement of the paddle, the
machine will automatically re-activate the
preservation cycle from the start.
TURNING OFF THE MACHINE DURING
PRESERVATION
To turn off the machine, hold down button (11)
for 3 seconds and then act on the main switch
(10). Do not act directly on the main switch (10)!
IMPORTANT
•Each preservation cycle continues until the
user decides to stop it.
•The machine is not designed for use either for
storage or as a refrigerator! Store the
preparation in the pot for no longer than 12
hours.
•The cooling fan of the cooling system will
always remain in operation for the entire
duration of the preservation period.
•After use, ALWAYS turn the machine off using
the main switch (10).
TIPS
•Using ingredients at refrigerator temperature
will reduce the processing time. Furthermore,
it is possible to reduce the temperature of the
ingredients if hot with the appropriate fast
cooling program.
•Be careful not to insert ingredients that are too
cold or nearly froze, as whipping may have a
poor quality.
•For a correct volume increase during mixing,
use maximum 1.5kg of ingredients for the
preparation of ice cream and sorbet.
•For the preparation of Granita, the maximum
amount of ingredients is 1.3Kg with the paddle
supplied with the machine.
It can process up to 1.8kg of Granita using the
special Granita paddle that can be purchased
separately.
10
English
CLEANING THE POT
GELATO 6K CREA is designed to facilitate pot
cleaning. Proceed as follows:
•Turn off the cooling system, remove the paddle
and pour at least 2 litres of hot water and a low-
foaming detergent into the pot.
•Wash the pot with a sponge. Do not use sharp
utensils inside the pot.
•Place an empty container of at least 3 litres
under the drain (7).
•Remove the plug (9). The water in the pot
begins to flow into the container below.
•Repeat the operation using hot, clean water
and rinse thoroughly.
•When the pot is empty, clean the discharge
pipe using the cleaner (21) previously
cleaned.
•Clean the plug (9). Reposition the plug (9) until
the pot discharge is fully closed.
•Repeat the cycle until the pot is completely
cleaned.
•Dry with a disposable paper towel.
•Proceed with the cleaning of the rest of the
machine.
MAINTENANCE AND CLEANING OF THE
MACHINE
•Before cleaning the machine, make sure that it
is turned off (main switch (10) to OFF) and
unplugged from the power plug.
•Remove the paddle scrapers (18) and (19) by
pulling outwards.
•Remove the steel pin and remove the
transparent lid (3) from the machine. .
•The paddle (5), paddle inserts (18) and (19),
transparent lid (3), the transparent lid cap (3a),
the silicon cap, the plug (9) and locking ring (4)
can be washed in the dishwasher or in hot
water with suitable detergent.
•If the paddle inserts are damaged or worn out,
they must be replaced to prevent mixing
ingredients less effectively.
•Clean the body of the machine and the non-
removable parts with the specific product
given in SANITIZATION chapter.
IMPORTANT: never wash the machine with jets
of water!
WARNING: when cleaning the stainless steel
parts of the machine do not use any chloride
based product (as the hydrochloric acid), nor
any bleach-hypochlorous-acid based
products nor any product containing strong
acid (such as those for the removal of cement
It contains electrical parts.