Product Description And Specifications - Bosch GWS 18-125 L Professional Notice Originale

OBJ_BUCH-3330-001.book Page 20 Tuesday, November 7, 2017 2:23 PM
20 | English
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, un-
fold the graphics page for the machine and leave it open.
Intended Use
The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
For cutting with bonded abrasives, a special cutting guard
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
With approved sanding tools, the machine can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
Technical Data
Angle Grinder
Article number
Rated power input
Output power
Rated speed
Speed control adjustment
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Kickback stop
Restarting Protection
Reduced starting current
Constant electronic control
Speed preselection
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
1 609 92A 3ZX | (7.11.17)
1 Release lever for protection guard
2 Spindle lock button
3 Thumbwheel for speed preselection
(GWS 18-125 SL/GWS 18-125 SPL)
4 On/Off switch
5 Auxiliary handle (insulated gripping surface)
6 Grinder spindle
7 Extraction hood for sanding*
8 Mounting flange with O-ring
9 Carbide grinding head*
10 Clamping nut
11 Quick-clamping nut
12 Protection guard for grinding
13 Grinding wheel*
14 Protection guard for cutting*
15 Cutting disc*
16 Hand guard*
17 Rubber sanding plate*
18 Sanding sheet*
19 Round nut*
20 Cup brush*
21 Cutting guide with dust extraction protection guard *
22 Diamond cutting disc*
23 Handle (insulated gripping surface)
24 Direction-of-rotation arrow for grinding spindle
25 Diamond core cutter*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GWS ... 18-125 L
3 601 ... GA3 0..
W 1800
W 1145
-1
min 12000
-1
min –
mm 125
M 14
mm 22




–
*
18-125 PL 18-125 SL 18-125 SPL
GA3 1.. GA3 2..
1800 1800
1145 1145
12000 12000
– 2800 – 12000 2800 – 12000
125 125
M 14 M 14
22 22
 
 
 
 

–
Bosch Power Tools
GA3 3..
1800
1145
12000
125
M 14
22




