Product Description And Specifications; Technical Data - Bosch GWS Professional 20-180 Notice Originale

OBJ_BUCH-721-005.book Page 9 Tuesday, August 30, 2011 2:58 PM
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
For cutting with bonded abrasives, a special cutting guide (ac-
cessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
With approved sanding tools, the machine can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Spindle lock button
2 On/Off switch
3 Auxiliary handle (insulated gripping surface)
4 Grinder spindle

Technical Data

Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions.
Malfunctions are not to be expected for system impedances below 0.25 ohm.
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales
service agent for maintenance (for addresses, see section
„After-sales Service and Customer Assistance".
Bosch Power Tools
5 Protection guard for grinding
6 Locking screw for protection guard
7 Mounting flange with O-ring
8 Grinding disc*
9 Clamping nut
10 Quick-clamping nut
11 Carbide grinding head*
12 Protection guard for cutting*
13 Cutting disc*
14 Protection guard for for grinding cup*
15 Grinding cup*
16 Hand guard*
17 Spacer discs*
18 Rubber sanding plate*
19 Sanding sheet*
20 Round nut*
21 Cup brush*
22 Cutting guide with dust extraction protection guard *
23 Diamond cutting disc*
24 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GWS 20-180 GWS 20-180 H
Professional Professional
0 601 849 1.. 0 601 849 1.. 0 601 850 1.. 0 601 850 1..
W 2000 2000
W 1250 1250
-1
min 8500 8500
mm 180
M 14 M 14
mm 25
kg 5.0
/II
Protection Guard for Grinding
Place the protection guard 5 on the spindle collar. Adjust the
position of the protection guard 5 to the requirements of the
operation and lock the protection guard 5 with the locking
screw 6.
Adjust the protection guard 5 in such a manner that
sparking is prevented in the direction of the operator.
Protection Guard for Cutting
For cutting with bonded abrasives, always use the pro-
tection guard for cutting 12.
English | 9
*
GWS 20-230 GWS 20-230 H
Professional Professional
2000 2000
1250 1250
6500 6500
180 230 230
M 14 M 14
25 25
5.0 5.3
/II /II
1 619 P09 125 | (30.8.11)
25
5.3
/II