DeWalt D27105 Manuel D'instructions page 44

E N G L I S H
- Right side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the left side of the cut.
Outside corner
- Left side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the right side of the cut.
- Right side
• Top of the moulding against the fence.
• Mitre right.
• Save the right side of the cut.
Sawing in the bench mode
• Always use the riving knife.
• Always ensure that the riving knife and blade guard are correctly
aligned.
• Always ensure that the mitre saw is set and locked in 0° mitre.
Do not cut metal in this mode.
Ripping (fig. U1 & U3)
• Set the bevel angle to 0°.
• Adjust the saw blade height.
• Set the parallel fence to the required distance.
• Hold the workpiece flat on the table and against the fence. Keep the
workpiece approx. 25 mm away from the saw blade.
• Keep both hands away from the path of the saw blade.
• Switch the machine on and allow the saw blade to reach full speed.
• Slowly feed the workpiece underneath the upper blade guard, keeping
it firmly pressed against the fence. Allow the teeth to cut, and do not
force the workpiece through the saw blade. The saw blade speed
should be kept constant.
• Remember to use the push stick (23) when close to the blade.
• After completing the cut, switch the machine off, allow the saw blade
to stop and remove the workpiece.
Never push or hold the free or cut-off side of the workpiece.
Always use a push stick when ripping small workpieces.
Bevel cuts (fig. U2)
• Set the required bevel angle.
• Proceed as for ripping.
Cross-cutting (fig. V1)
• Set the bevel angle to 0°.
• Adjust the saw blade height.
• Set the mitre fence to 0°.
• Proceed as for ripping, only use the mitre fence to push the workpiece
through the blade.
Bevel cross-cutting
• Set the required bevel angle.
• Proceed as for cross-cutting.
Mitre cuts (fig. V2)
• Set the mitre fence to the required angle.
• Proceed as for cross-cutting.
44
All manuals and user guides at all-guides.com
Optional attachments
Dust extraction kit (fig. W1 & W2)
This machine is provided with two dust extraction points for use in each
mode.
• When sawing wood, connect a dust extraction device designed in
Connecting - mitre saw position (fig. W1)
• Connect the one end of the first hose to the dust extraction adaptor (13).
• Insert the other end of the hose into the middle inlet port of the
• Connect the one end of the other hose to the under-table guard (63).
• Insert the other end of the hose into the outer inlet port of the manifold.
Connecting - saw bench position (fig. W2)
• Proceed as for mitre saw position, only connect the hose from the
Mitre saw extra support/length stop (fig. A5)
The extra support and length stop can be mounted on the left-hand side
or on the right-hand side, or with two sets on either side.
• Fit the items 31 - 39 onto the two guide rails (32 & 33).
• Use the inclinable support (34) for cross-cutting 210 mm wide boards
Roller support table (fig. A6)
The roller support table (40) is used to support long workpieces. In mitre
saw mode, the roller support table can be mounted on the left-hand side
or on the right-hand side, or with two sets on either side. In saw bench
mode, it can also be mounted in front or at the rear of the saw table.
Side extension table (fig. A8)
The side extension table increases the distance from the rip fence to the
blade to 600 mm or more, depending on the rod length fitted to the
machine and the clamped position of the table. The side extension table
must be used in conjunction with guide rails (33) (option). The adjustable
table is equipped with an engraved scale along its front edge and
mounted on a sturdy base which clamps to the guide rods.
• Fit the extension table to the right-hand side of the machine for
Sliding table (fig. A9)
This sliding table (43) allows for board sizes to the left of the blade up to
1200 x 900 mm.
The guide rods are mounted on a sturdy alloy extrusion which is quickly
detachable from the machine and yet fully adjustable is all planes.
The fence incorporates a full length measuring tape for quick positioning of
an adjustable stop and an adjustable support for narrow workpieces.
Saw bench guard
In countries where the Suva-type guard is a legal requirement, it is
supplied as standard. In other countries, it is available as an option.
Transporting (fig Y)
The castor wheels provide an easier transport of the machine.
• Fold the rear legs into the base.
• Fold the front legs out of the base.
Prior to assembling any accessories always unplug the machine.
accordance with the relevant regulations regarding dust emission.
manifold (128).
under-table guard to the saw blade guard (21).
(15 mm thick).
continuity of the distance scale on both tables.
Always transport the machine in saw bench mode with the
upper blade guard fitted.