DeWalt D27105 Manuel D'instructions page 37

Safety instructions
When using stationary power tools, always observe the safety
regulations applicable in your country to reduce the risk of fire,
electric shock and personal injury.
Read all of this manual carefully before operating the tool.
Save this manual for future reference.
General
1 Keep work area clean
Cluttered areas and benches can cause accidents.
2 Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250 - 300 Lux). Do not use the
tool where there is a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
3 Keep children away
Do not allow children, visitors or animals to come near the work area or
to touch the tool or the mains cable.
4 Dress properly
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Wear protective hair covering to keep long hair out of the
way. When working outdoors, preferably wear suitable gloves and
non-slip footwear.
5 Personal protection
Always use safety glasses. Use a face or dust mask whenever the
operations may produce dust or flying particles. If these particles might
be considerably hot, also wear a heat-resistant apron. Wear ear
protection at all times. Wear a safety helmet at all times.
6 Guard against electric shock
Prevent body contact with earthed or surfaces (e.g. pipes, radiators,
cookers and refrigerators). When using the tool under extreme
conditions (e.g. high humidity, when metal swarf is being produced,
etc.), electric safety can be improved by inserting an isolating
transformer or a (FI) earth-leakage circuit-breaker.
7 Do not overreach
Keep proper footing and balance at all times.
8 Stay alert
Watch what you are doing. Use common sense. Do not operate the
tool when you are tired.
9 Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it frees both
hands to operate the tool.
10 Connect dust extraction equipment
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly used.
11 Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed from the
tool before operating the tool.
12 Extension cables
Before use, inspect the extension cable and replace if damaged.
When using the tool outdoors, only use extension cables intended for
outdoor use and marked accordingly.
13 Use appropriate tool
The intended use is described in this instruction manual. Do not force
small tools or attachments to do the job of a heavy-duty tool. The tool
will do the job better and safer at the rate for which it was intended.
Do not force the tool.
Warning! The use of any accessory or attachment or performance of
any operation with this tool other than those recommended in this
instruction manual may present a risk of personal injury.
14 Check for damaged parts
Before use, carefully check the tool and mains cable for damage.
Check for misalignment and seizure of moving parts, breakage of
parts, damage to guards and switches and any other conditions that
may affect its operation.
All manuals and user guides at all-guides.com
15 Unplug tool
16 Avoid unintentional starting
17 Do not abuse cord
18 Store idle tools
19 Maintain tools with care
20 Repairs
Additional safety rules for mitre saws
• Make sure all locking knobs and clamp handles are tight before starting
• Do not operate the machine without the guard in position, or if the
• Never place either hand in the blade area when the saw is connected
• Never attempt to stop a machine in motion rapidly by jamming a tool or
• Before using any accessory consult the instruction manual.
• Select the correct blade for the material to be cut.
• Observe the maximum speed marked on the saw blade.
• Use a holder or wear gloves when handling a saw blade.
• Make sure that the blade rotates in the correct direction.
• The max. allowable speed of the saw blade must always be equal to or
• Do not use saw blades that do not conform to the dimensions stated in
• Consider applying specially designed noise-reduction blades.
• Do not use HSS blades.
• Do not use cracked or damaged saw blades.
• Do not use any abrasive discs.
• After completing the cut, release the switch and wait for the saw blade
• Ensure that the arm is securely fixed when performing bevel cuts.
• Do not wedge anything against the fan to hold the motor shaft.
• The blade guard on your saw will automatically raise when the arm is
Ensure that the tool will operate properly and perform its intended
function. Do not use the tool if any part is damaged or defective.
Do not use the tool if the switch does not turn it on and off. Have any
damaged or defective parts replaced by an authorised D
agent. Never attempt any repairs yourself.
Switch off and wait for the tool to come to a complete standstill before
leaving it unattended. Unplug the tool when not in use, before changing
any parts of the tools, accessories or attachments and before servicing.
Be sure that the tool is switched off before plugging in.
Never pull the cord to disconnect from the socket. Keep the cord away
from heat, oil and sharp edges.
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
Keep the tools in good condition and clean for better and safer
performance. Follow the instructions for maintenance and changing
accessories. Keep all handles and switches dry, clean and free from oil
and grease.
This tool is in accordance with the relevant safety regulations.
Have your tool repaired by an authorised D
Repairs should only be carried out by qualified persons using original
spare parts; otherwise this may result in considerable danger to the user.
any operation.
guard does not function or is not maintained properly.
to the electrical power source.
other means against the blade; serious accidents can be caused
unintentionally in this way.
The improper use of an accessory can cause damage.
Keep the blade sharp.
greater than the no-load speed of the tool specified on the nameplate.
the technical data. Do not use any spacers to make a blade fit onto the
spindle. Use only the blades specified in this manual, complying with
EN 847-1.
to come to a complete stillstand before returning the head to its upper
rest position.
brought down; it will lower over the blade when the arm is raised.
The guard can be raised by hand when installing or removing saw
blades or for inspection of the saw. Never raise the blade guard
manually unless the saw is switched off.
E N G L I S H
WALT repair
E
WALT repair agent.
E
37