DeWalt D27105 Manuel D'instructions page 38

E N G L I S H
• Keep the surrounding area of the machine well maintained and free of
loose materials, e.g. chips and cut-offs.
• Check periodically that the motor air slots are clean and free of chips.
• Disconnect the machine from the mains before carrying out any
maintenance work or when changing the blade.
• Never perform any cleaning or maintenance work when the machine is
still running and the head is not in the rest position.
• The front section of the guard is louvred for visibility while cutting.
Although the louvres dramatically reduce flying debris, there are
openings in the guard and safety glasses should be worn at all times
when viewing through the louvres.
Additional safety rules for saw benches
• Do not use saw blades with a body thickness greater or a width of
tooth smaller than the thickness of the riving knife.
• Make sure that the blade rotates in the correct direction and that the
teeth are pointing to the front of the saw bench.
• Be sure all clamp handles are tight before starting any operation.
• Be sure all blade and flanges are clean and the recessed sides of the
collar are against the blade. Tighten the arbor nut securely.
• Keep the saw blade sharp and properly set.
• Make sure that the riving knife is adjusted to the correct distance from
the blade - maximum 5 mm.
• Never operate the saw without the upper and lower guards in place.
• Keep your hands out of the path of the saw blade.
• Disconnect the saw from the mains supply before changing blades or
carrying out maintenance.
• Use a push stick at all times, and ensure that you do not place hands
closer than 150 mm from the saw blade while cutting.
• Do not attempt to operate on anything but the designated voltage.
• Do not apply lubricants to the blade when it is running.
• Do not reach around behind the saw blade.
• Always keep the push stick in its place when not in use.
• Do not stand on top of the unit.
• During transportation make sure that the upper part of the saw blade is
covered, e.g. by the guard.
• Do not use the guard for handling or transportation.
Additional safety rules for flip-over saws
• Ensure that the arm is securely fixed in the working position in the
bench sawing mode.
• Ensure that the arm is securely fixed when bevelling in the bench saw
mode.
• Ensure the table is correctly locked when changing the saw mode.
• Take care when grooving during the bench saw operation by using
appropriate guarding system. Slotting is not allowed.
Residual risks
The following risks are inherent to the use of saws:
- injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
- Impairment of hearing.
- Risk of accidents caused by the uncovered parts of the rotating saw
blade.
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.
38
All manuals and user guides at all-guides.com
Labels on tool
The following pictograms are shown on the tool:
Package contents
The package contains:
1 Partly assembled machine
1 Box containing:
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
• Take the time to thoroughly read and understand this manual prior to
Description (fig. A1 - A10)
Your D27105 flip-over sawing machine has been designed to operate as a
mitre saw or as a saw bench to perform the four main sawing operations
of ripping, cross-cutting, bevelling and mitring easily, accurately and safely.
Mitre saw mode
In mitre saw mode, the sawing machine is used in vertical, mitre or bevel
position.
Saw bench mode
Turned over on its central axis, the sawing machine is used to perform the
standard ripping operation and for sawing wide pieces by manually
feeding the workpiece into the blade.
Features
A1
1 On/off switch (saw bench mode)
2 Table release lever
3 Rotating table clamp
4 Mitre saw table
5 Rotating table
6 Fence right-hand side
7 Fence left-hand side
8 Moveable lower blade guard
9 Guard release lever
10 Operating handle
A2
10 Operating handle
11 Trigger switch (mitre saw mode)
12 Fixed upper blade guard
13 Dust extraction adapter
14 Wheel
15 Leg
When using the machine in the mitre saw mode, make sure to
operate the trigger switch when switching on and off.
Do not operate the switchbox in this mode.
When using the machine in the bench saw mode, make sure
that the riving knife has been mounted. Do not use the
machine without the riving knife.
1 Top guard for bench saw position
1 Under-table guard for mitre saw position
4 Legs
2 Wheels
4 Feet
1 Parallel fence
occurred during transport.
operation.