Publicité
Les langues disponibles
Les langues disponibles
Δｔｄ
Heating set temperature
(remote control set
temperature
+
SHI TW)
Dash period
an speed set to "auto"
an speed set to "auto"
Start
Start / Stop switch
Thermo judgmet
Max. 3min.
Room temperature Ð outdoor temperature
Room temperature Ð outdoor temperature
Defrost signal
Preheating judgment
Preheating released
Ultra-Hi
Hi
Med
Indoor fan
Lo
Control by heat exchanger temperature
Silent Sleep
Ultra-Lo
Hot keep lamp
(Duct type only)
Operation lamp
RPMKEP
Max.
(WMAX1)
Preheating period is WMAX1 or WMAX2
(WMAX2)
Rating
Starting rotation speed
(TSKTM1_W1 or TSKTM1_W2)
Min.
(MINRPM)
０
an tap is controlled from outdoor unit.
Outdoor fan
Reversing valve (cooling "on" mode)
Notes:
(1) Hot Dash is started when the operation is started at fan speed ÒAUTOÓ or ÒHIÓ or when the fan speed is changed to ÒAUTOÓ or ÒHIÓ during heating operation, and when the compressor speed
(P item) reaches (WMAX1 or WMAX2) or higher with the room temperature at 8
(2) The maximum compressor speed period during hot dash is finished (1) when the room temperature reaches the heating set temperature (including heating shift) plus S TDSW or (2) when the
thermo is off.
(3) The thermo O
temperature during hot dash is heating set temperature (including heating shift) plus 3
(4) The compressor minimum ON time and minimum O
(5) The time limit for which the maximum compressor speed (WMAX1 or WMAX2) during normal heating (except for hot dash) can be maintained is less than 120 minutes when the room temperature is
18
or more; it is not provided when the room temperature is less than 18
℃
(6) The operation indicator will blink every second during initial cycle operation, preheating, defrosting (including balance time after defrost is finished), or auto fresh defrosting. However, with duct type
models, operation indicator does not blink, but Hot Keep indicator will light. And Hot Keep indicator will also light in ÒThermo O Ó mode.
(7) or preheating judgment, preheating starts if the heat exchange temperature is lower than YNEO and is cancelled if the heat exchange temperature is YNEO plus 0.33
operation using the START / STOP button.
(8) If the room temperature falls to less than 18
in the "Ultra-Lo" mode, the indoor fan stops. When the room temperature is 18
℃
Lo operation during preheating or preheating after defrosting does not stop if the room temperature is less than 18
(9) Compressor speed is determined by instruction sent from indoor unit and corrected by outdoor unit according to such factors as capacity, fan speed, number of units being operated, outdoor
temperature, etc.
(10) If another indoor unit is doing cooling operation, dehumidifying operation or fan operation, heating operation cannot be done.
All manuals and user guides at all-guides.com
eating Basic Operation
Thermo
Thermo
Stop
Start
Stop
O
O
It is Ultra high speed when it is RTOSTA
It is Ultra high speed when it is RTOSTA
≧
≧
Control by heat exchanger temperature
Control by heat exchanger temperature
Control by heat exchanger temperature
Control by heat exchanger temperature
15sec.
15sec.
15sec.
or less and outdoor temperature at 10
℃
. After thermo O , hot dash finishes, and PI control starts.
℃
time is 3 minutes.
and outdoor temperature is less than 4
℃
18
℃
Thermo
Thermo
Start
O
O
Preheating released
Control by heat exchanger temperature
Control by heat exchanger temperature
Control by heat exchanger temperature
10set
Preheating period is
WMAX1 or WMAX2
3min.
15sec.
or less.
℃
.
℃
+0.33
or more, the ultra-Lo operation restarts. However, the ultra-
℃
℃
.
℃
Stop
15sec.
or higher at the start of
℃
- 215 -
Publicité
