Publicité
Les langues disponibles
Les langues disponibles
Expanded system (+1)
�he call number for internal calls will be shown in
the display in standby mode. �he base unit should be
positioned centrally so that the coverage area is roughly
equal for all handsets.
Intercom / internal call
1. Press
(right menu button).
2. If using more than 2 handsets: Enter call number
for the desired handset or press
A tone will be heard if an external call comes in while an
internal call is in progress. End the internal call with
and then answer the external call with
Transferring calls/Conference between handsets
When an external call is connected;
1. Press
. Scroll to INTERCOM. Press OK.
2. If using more than 2 handsets: Enter call number
for the desired handset or press
3. �o transfer: press
L
pressed down.
Register a new handset
All handsets included in the package are already registered
to the base unit.
Only for separate handsets/service measures.
You can register up to 6 handsets to one base unit.
This model is GAP (Generic Access Profile) compatible,
which means that the handset and the base unit can both be
used with most other GAP compatible units irrespective of
manufacturer. However the GAP protocol cannot guarantee
that all functions may be accessed. Extra handsets will not be
available as accessories.
1. Hold down
on the base unit until indicator flashes.
J
2. Press
. Scroll to REGISTRATION. Press OK.
3. Enter the base unit's PIN code (e.g. 0000). Press OK.
4. If the registration is successful the unit will return to
standby mode within one minute.
for all.
9
.
q
for all.
9
, �or conference: hold
English
Answer machine (only NeoBio 15r/25r)
When the answer machine is switched on calls are answered
after a set number of rings, your outgoing message is heard
and the caller can leave a message. �otal memory capacity
is up to 15 minutes depending on the set sound quality
(NeoBio 15r), or 30 min (NeoBio 25r). Most functions can
be accessed from both base unit and handset.
-
1
6
Switching the answer machine on/off
Press
(on the base unit) to switch the answer machine
1
off/on. If the base unit's display is flashing/showing
-- the answer machine is disconnected, or time/date is
L
not set.
Off/On from the handset
1. Press
. Scroll to ANS. MACHINE. Press OK.
2. Scroll to TAM OFF/ON. Press OK.
3. Scroll to desired setting. Press OK.
-
1
6
If the handset's display shows
answer machine is switched on. If there are new messages,
*
the indicator will flash whether the answer machine is off
or on.
Outgoing message
�he outgoing message (max 3 min) is heard by incoming
calls. �here are two separate outgoing messages, one for
Answer only (callers cannot leave a message) and one for
normal answering function.
1. Press
. Scroll to ANS. MACHINE. Press OK.
2. Scroll to TAM SETTINGS. Press OK.
3. Scroll to OGM SETTINGS. Press OK.
4. Scroll to ANSWER & REC/ANSWER ONLY. Press OK.
5. Scroll to RECORD MESS. Press OK.
6. After the long beep you can record your message
(speaking approx. 20 cm from the keypad). Press OK.
7. �he message will be played back to you. Repeat the
above to change.
Also select desired answer function. See TAM Settings.
Screening
Incoming messages will be heard on the loudspeaker of
the base unit as they are received. If nothing can be heard,
check that the volume is turned up and that the function
has been activated – see separate description. You can also
press OK on the handset while recording is in progress.
�he call can be intercepted by pressing
receiver of another telephone connected to the same line.
with a steady light the
or lifting the
q
Publicité
