DeWalt XR DCF620 Traduction De La Notice D'instructions Originale page 33

Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1 Depth locator
2 Screw depth adjustment
collar
3 Locking collar
4 Nose cone
5 Battery release button
6 Battery pack
Collated Magazine attachment DCF6201/DCF6202 (Fig. E)
(available separately)
12 Screw guide
13 Screw length adjustment
14 Fine depth adjustment
15 Advancing mechanism
16 Shoe
Intended Use
Your drywall screwdriver has been designed for driving
drywall fasteners through drywall board into timber or metal
framing studs.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This drywall screwdriver is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Dead Spindle Drive Clutch
This screwdriver is equipped with a dead spindle feature; the
spindle does not turn until the fastener is pressed into the
workpiece. This enables fasteners to be placed onto the drive
accessory of a running screwdriver.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
7 Trigger switch
8 Forward/reverse control
lever
9 Lock-on button
10 LED worklight
11 Belt hook
17 Advancing mechanism
removal catch
18 Release Buttons
19 Collated attachment
screwdriver bit
WALT battery packs and chargers.
e
6
is fully charged.
To Install the Battery Pack into the Tool Handle
6
1. Align the battery pack
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
20
button . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Changing Bit Holders (Fig. C)
1. Rotate the locking collar
from gear case.
4
2. Pull nose cone off of gear case.
3. To remove:
22
a. Grab the bit holder
b. Push it into the gear case depressing the sleeve
c. Rotate the bit holder until the clutch engages.
d. While holding the sleeve depressed, pull the bit
holder out.
4. Push and rotate the new bit holder into gearcase,
depressing the sleeve, until ball lock snaps in groove in bit
holder shank.
4
5. Replace nose cone by placing on gear case and rotating
collar 1/4 turn to align arrow on gear case with the lock
symbol on collar.
Changing Bit Tip (Fig. C)
1. Rotate the locking collar
from gear case.
2. Pull forward on nose cone
clutch housing.
3. Use pliers to remove worn bit and install new bit tip.
Depth Adjustment
Follow the graphic on the collar to increase or decrease the
fastening depth. To seat the screw deeper in the workpiece, turn
the adjustment collar to the right. To seat the screw higher in
the workpiece, turn the adjustment collar to the left.
EngLIsh
with the rails inside the tool's
5
and firmly pull the battery pack
3
1/4 turn to unlock nose cone
.
21
3
1/4 turn to unlock nose cone
4
and remove it from
.
31