Setting Up And Connecting The Unit - Monacor DMP-130MIX Mode D'emploi

4 Setting Up and
Connecting the Unit
Prior to making or changing any connections,
switch off the DMP-130MIX and the units to
be connected .
1) The jack MIC (5) is used to connect a mi-
crophone with XLR plug or 6 .3 mm plug .
2) The RCA jacks INPUT (18) are used to con-
nect a stereo unit with line output (CD
player, radio, tape deck, etc .) .
If the integrated MP3 player is not
used, it is possible to connect another ste-
reo unit with line output to the 3 .5 mm
jack AUX (6) . If you use the jack, the MP3
player will be muted .
3) To route the sum signal, e . g . to an ampli-
fier, two outputs are available which can
be used at the same time:
the RCA jacks OUTPUT (19) and
the XLR connectors OUTPUT (20)
A balanced connection via the XLR output
is less susceptible to interference; therefore
the XLR output should be preferred to the
RCA output .
4) First connect the mains cable provided to
the mains jack (21); then connect it to a
mains socket (230 V / 50 Hz) .
5 Operation
Switch on the unit with the POWER switch (4) .
The display (7) shows
No Disk
. If a memory card or USB flash
Add Disk
drive has been inserted or a hard disk has
been connected and this medium has been
loaded, the display will show the number of
titles: *...
Total Song: U
* U = USB storage medium is selected
S = memory card is selected
The second line shows the message
. To start the replay, press the
Enter Key
button  II (10) .
5.1 Mixing the audio signals
1) Set the controls MIC (13), AUX / MP3 (14)
and LINE (15) of the input channels not
used to MIN . For the time being, set the
other controls to mid-position .
2) Feed an audio signal to each of the input
channels and set the output level with the
INPUT OUTPUT
CD/LINE UNBAL.
L L
R R
18 19
control VOLUME (16) in such a way that
the subsequent unit is perfectly adjusted .
3) Adjust the sound of the output signal with
the controls TREBLE and BASS (17) .
4) Use the controls MIC, AUX / MP3 and LINE
to mix the audio signals or to fade them
in and out . If necessary, adjust the output
level with the control VOLUME .
5.2 MP3 player
Do not connect a plug to the jack AUX (6),
otherwise the MP3 player will be muted .
1) Connect a USB flash drive
to the USB port (3)
and / or
insert an SD / MMC memory card
slot SD (2), the notched corner to the right
and facing the unit . To remove the card,
slightly push the card into the slot until it
disengages .
1 Due to the large number of storage device
manufacturers and device drivers, it cannot be
guaranteed that all storage media are compati-
ble with the DMP-130MIX .
2 The hard disk must have one partition only and
must be supplied with power via a separate
power supply unit .
2) Press the button  II (10) to start the first
title . The display shows
(e) next to it alternately shows the time
already played of the title and the playing
time of the title .
Please
3) To switch between USB storage me-
dium and memory card, press the button
USB / SD (1) . Field (a) of the display shows
the storage medium selected:
U = USB storage medium
S = SD card
4) To go to the next or previous title, briefly
Please
press the button I   or  I (11) . The dis-
play shows the title number on the top
left (b) and next to it in the field (c) the
title name if it is stored as an ID3 tag in
the audio file .
5) For fast forward, keep the button  I
pressed; for fast reverse, keep the button
I   pressed . Fast forward / reverse is only
possible within a title . You will not be able
to trace it acoustically, only via the time
indication (e) on the display .
All rights reserved by MONACOR
may be reproduced in any form or by any means for any commercial use.
OUTPUT
RIGHT LEFT
BAL.
20
1 or a hard disk 2
into the
1
(d) . The field
Play
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual
21
230 V~
DMP-130MIX
MP3 PLAYER AND MIC/LINE MIXER
22
6) To switch between replay [indication
(d)] and pause [indication
the button  II .
7) To switch between repeat of all titles [in-
dication (f)] and continuous repeat
All
of the current title [indication
the button REPEAT (8) .
8) The button EQ (12) is used to select vari-
ous sound adjustments for the MP3 player .
The adjustment selected is briefly shown
in field (d) of the display .
9) To stop the replay, press the button ⬛ (9) .
The display shows
Stop
on the left (d) and the number of titles
above it (b) .
6 Specifications
Frequency response: . .20 – 20 000 Hz
THD: . . . . . . . . . . . . . .< 0 .1 %
Channel separation: . .> 60 dB
Dynamic range: . . . . . .> 96 dB
S / N ratio: . . . . . . . . . .> 70 dB
Inputs
Sensitivity / impedance; connection
MIC: . . . . . . . . . . . . .2 .5 mV / 500 Ω;
XLR and 6 .3 mm
jack, bal .
AUX: . . . . . . . . . . . .350 mV / 7 .5 kΩ;
3 .5 mm jack, stereo
LINE: . . . . . . . . . . . . .850 mV / 20 kΩ; RCA
Output level
XLR, bal .: . . . . . . . . .2 V
RCA: . . . . . . . . . . . .1 V
Power supply: . . . . . . .230 V / 50 Hz
Power consumption: . .20 VA max .
Ambient temperature: .0 – 40 °C
Dimensions
(W × H × D): . . . . . . . .482 × 44 × 160 mm,
1 RS (rack space)
Weight: . . . . . . . . . . .2 .2 kg
Subject to technical modification .
50 Hz
FUSE
Play
], press
Pause
], press
One
at the bottom
7