Removing/Inserting The Battery - Milwaukee FORCE LOGIC M18 2776-20 Manuel De L'utilisateur

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Blades are sharp. Keep hands away from cutting
edge. Laceration can occur.
Changing the Blades
Replace the blades when they become chipped or
damaged. Always replace blades as a set. Use only
MILWAUKEE blades. Refer to Specifications for
replacement blade numbers.
1. Pull the trigger to close the blades slightly. The
retaining rings must be exposed.
2. Remove the battery pack.
3. Use a wrench or pliers to remove the blade nut
and remove the blade bolt. Discard the blade nut.
4. Remove the retaining ring and pull out the pin
from one of the blades.
5. NOTE: Take notice of the blade orientation so the
new blades can be installed the same way. The
blades should be oriented so the flat sides contact
and the bevels face away from each other, like a
pair of scissors.
6. Carefully remove the blade.
7. Install the new blade in the
same orientation.
8. Slide the pin through the
blade and bracket. Replace
the retaining ring. NOTE:
The pins must be installed
with the retaining rings on
the inside of the blades, the
pin heads facing outwards.
9. Repeat steps 4 to 8 for the other blade.
10. Insert the blade bolt.
11. Thread the new blade nut onto the blade bolt.
Tighten the nut to 150 in-lbs, then back it off
between 1/4 and 1/2 turn.
NOTE: To ensure proper installation, perform a test
cut. If the blades bind when opening, loosen the blade
nut slightly until the blades no longer bind.
Locking and Unlocking the Trigger
To lock the trigger, pull the trigger lock back.
To unlock the trigger, push the trigger lock forward.
ONE-KEY™
To learn more about the ONE-KEY™ function-
ality for this tool, please reference the Quick
Start guide included with this product or go to
milwaukeetool.com/One-Key. To download the
ONE-KEY™ app, visit the App Store or Google Play
from your smart device.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
To reduce the risk of arc flash,
WARNING
electric shock and property
damage, work on deenergized lines when
possible. Tool is not insulated. Should work
on energized lines be required, ensure all proper
precautions, including those contained in NFPA
70E, have been taken first.
Keep hands away from all cutting edges and
moving parts. Laceration and amputation
can occur.
Always remove battery pack before changing or
removing accessories. Only use accessories spe-
cifically recommended for this tool. Others may be
hazardous.
Always wear proper eye protection marked to
comply with ANSI Z87.1.
• Before cutting, ensure blades are properly installed.
• The tool can be set on the ground or hand held
during use. To set the tool on the ground, rotate
the cutting head 180° to use the front handle as a
"foot". To hold by hand, grasp the tool firmly by both
handles, as shown.
• Insert the workpiece squarely between the blades.
Do not attempt to make angled cuts as it will dam-
age the workpiece and blades.
1. Grasp handle(s) firmly and pull and hold the trigger
through the operation. When the cut is complete or
the tool shuts off, release the trigger. An LED will
light when the trigger is pulled. NOTE: Workpiece
may move slightly during the cut.
2. When the cut is complete, pull the release trigger
to open the blades.
To reduce the risk of injury, only
WARNING
cut recommended materials for the
blades (see "Specifications"). Do not attempt to
cut other materials.
4
Cutting