120 Vac Grounding Instructions; Unpacking; Machine Description; Micromax™ 17E Automatic Scrubber Operation - Nilfisk Advance Micromax 17E Instructions D'utilisation

INSTRUCTIONS FOR USE

120 VAC GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should electrically
malfunction, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This
appliance is equipped with a cord having an
equipment-grounding conductor and grounding plug. The
plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances.
WARNING!
The machine must be used with an extension
power cord as follows:
– minimum length 15 feet
– type S, or ST, or SO, or STO, or STW
– minimum rate 300V 140/167°F (60/75°C)
DANGER!
Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified
electrician or service person if you are in doubt as to whether
the outlet is properly grounded. Do not modify the plug
provided with the appliance. If it will not fit the outlet, have a
proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120 V circuit, and has
a grounding plug that looks like the plug (B, Fig. G). A
temporary adapter (B and C, Fig. G) may be used to connect
this plug to a 2-pole receptacle (B), if a properly grounded
outlet is not available. The temporary adapter should be used
only until a properly grounded outlet (A, Fig. G) can be installed
by a qualified electrician. The green-colored rigid ear, tab, or
the like extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in place
by a metal screw. Grounding adapters are not approved for
use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or Green/Yellow) wire in the cord is the grounding
wire. When replacing a plug, this wire must be attached to the
grounding pin only.
– Extension cords connected to this machine should be 12
gauge, three-wire cords with three-prong plugs and
outlets. DO NOT use extension cords more than 50 feet
(15 m) long.

UNPACKING

To unpack the machine carefully follow the instructions on the
packing.
On delivery, check that the machine and its packing were not
damaged during transportation. If the damages are evident,
keep the packing and have it checked by the Parcel Service
that delivered it. Call the Parcel Service immediately to fill in
a request for a compensation for damages.
Please check that the following items have been supplied with
the machine:
– Technical documents:
– Instructions for Use
– Spare Parts List
– Extension cord (in case the machine is supplied with
the "no-touching ground" power cord).
4
All manuals and user guides at all-guides.com

MACHINE DESCRIPTION

MICROMAX™ 17E AUTOMATIC
SCRUBBER OPERATION
The scrubber-dryer is used to clean (scrubbing and drying)
smooth and solid floors, in civil or industrial environment,
under safe operation conditions and by a qualified Operator.
The scrubber-dryer cannot be used for fitted carpet and
carpet cleaning.
AGREEMENTS
Forward, backward, front, rear, left or right are intended
with reference to the Operator's position with the hands on
the handlebar (2, Fig. C).
Control panel and commands
(See Fig. B)
1.
2.
3.
4.
5.
Exterior rear overview
(See Fig. C)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Squeegee
11. Squeegee fastening knob
12. Squeegee balancing knob
13. Squeegee front blade
14. Squeegee rear blade
15. Rear blade fastening hook
16. Wing nuts
17. Recovery water drain hose
18. Solution drain hose
19. Squeegee lifting lever
20. Brush lifting pedal
21. Solution filter
22. Machine electric supply plug
23. Machine electric supply cable
24. Supplied key
25. Squeegee vacuum hose
26. Solution tank marks
27. Solution tap
28. Rubber band
29. Spoiler
Front under cover and tank exterior overview
(See Fig. H)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Vacuum motor
11. Brush motor
Control panel and commands
Brush rotation switch
Vacuum switch
Solution flow control lever
Control panel and commands mounting screws
Serial number plate/technical data
Handlebar
Handlebar inclination adjusting handles
Can holder
Tank cover
Rear wheels, steering
Front wheels on fixed axle
Brush, or pad-holder and pad
Brush/pad-holder deck
Tank assembly fastening screw
Tank cover (open position)
Tank cover seal
Compensation hole
Recovery water tank
Solution tank
Recovery water vacuum hole
Vacuum grid with automatic float cut-off
Recovery water draining hole
Micromax™ 17E — 909 5473 000(2)2005-04