Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
FITTING INSTRUCTIONS FOR CP0290 CRASH PROTECTORS
HONDA CROSS RUNNER 2011
Page | 1
PICTURE 'A'
PICTURE 'B'
REAR OF BIKE
FRONT OF BIKE
PICTURE 'C'
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike
Please note that in cases where kits are packed with rubber washers holding the components onto
the bolt – the rubber washers should be thrown away!
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
Manuels Connexes pour R&G TTLRG-CP0290-BL
Sommaire des Matières pour R&G TTLRG-CP0290-BL
- Page 1 FITTING INSTRUCTIONS FOR CP0290 CRASH PROTECTORS HONDA CROSS RUNNER 2011 Page | 1 PICTURE ‘A’ PICTURE ‘B’ REAR OF BIKE FRONT OF BIKE PICTURE ‘C’ THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike Please note that in cases where kits are packed with rubber washers holding the components onto...
-
Page 2: Left Hand Side
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY FOR CLARITY OF INSTRUCTIONS ONLY Page | 2 LEFT HAND SIDE RIGHT HAND SIDE R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com... -
Page 3: Additional Equipment
Page | 3 ADDITIONAL EQUIPMENT TOOLS REQUIRED Socket set to include 14 and 17mm sockets and wrench. Set of metric Allen keys to include 5mm A/F. Torque wrench (up to 40Nm). LEGEND ITEM 1 = BC0002 CRASH PROTECTOR CAPS (x2). ITEM 2 = B0431 with CS341 (10mm) (BOTH CRASH PROTECTORS) (x2). -
Page 4: Fitting Instructions
FITTING INSTRUCTIONS Page | 4 Near side (left side as you sit on bike) Remove the engine/frame bolt in position arrowed at top of picture ‘D’ (using 14mm socket), you may have to loosen the fairing panel (bolt and plastic push rivet) to allow the bolt to be removed. ... - Page 5 CONSUMER NOTICE The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes.
-
Page 6: Avant De La Moto
FRANCE INSTRUCTIONS DE MONTAGE DES PROTECTIONS CP0290 HONDA CROSS RUNNER 2011 Page | 6 ARRIERE DE LA MOTO AVANT DE LA MOTO ’ ’ R&G A PRESENTATION DES PIECES DANS L EMBALLAGE N EST PAS TOUJOURS IDENTIQUE AU SENS DE MONTAGE Merci de noter que dans le cas où... - Page 7 INSTRUCTIONS Gauche Enlever la vis de fixation moteur montrée en photo « D », utiliser la clef à douille de 14mm, vous aurez probablement besoin de desserrer le carénage (vis et rivet en plastique) pour avoir accès à la Page | 7 vis de fixation moteur.