Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
FITTING INSTRUCTIONS FOR CP0281 CRASH PROTECTORS
HONDA CBR 125R 2011
Page | 1
PICTURE 'A'
PICTURE 'B'
REAR OF BIKE
FRONT OF BIKE
PICTURE 'C'
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike
Please note that in cases where kits are packed with rubber washers holding the components onto
the bolt – the rubber washers should be thrown away!
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
Manuels Connexes pour R&G RG.CP0281BL
Sommaire des Matières pour R&G RG.CP0281BL
- Page 1 FITTING INSTRUCTIONS FOR CP0281 CRASH PROTECTORS HONDA CBR 125R 2011 Page | 1 PICTURE ‘A’ PICTURE ‘B’ REAR OF BIKE FRONT OF BIKE PICTURE ‘C’ THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike Please note that in cases where kits are packed with rubber washers holding the components onto...
- Page 2 HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY FOR CLARITY OF INSTRUCTIONS ONLY Page | 2 LEFT HAND SIDE R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 3 THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Page | 3 RIGHT HAND SIDE TOOLS REQUIRED • Socket set to include 12mm and 17mm sockets and wrench • Set of metric Allen keys 4,5,6 and 8mm A/F •...
- Page 4 LEGEND ITEM 1 = M10x1.25x100mm LONG HEX HEAD BOLTS. ITEM 2 = M10 PLAIN WASHERS (x2). ITEM 3 = LW0001 (M12 SHAKE PROOF WASHERS) (x2). ITEM 4 = B0063 with CS066 (10mm) (BOTH CRASH PROTECTORS) (x2). ITEM 5 = S0191 ( SPACERS 51.5mm LONG) (x2). Page | 4 ITEM 6 = 100mm LENGTH OF SELF ADHESIVE FOAM (x2).
- Page 5 • Take two of the (30mm) cap head bolts with washers and locate in the two holes in mounting block and into the frame mount as shown in picture ‘D’. • Tighten both bolts evenly. • Fit the marking tool (shown in picture) into remaining hole. •...
- Page 6 • Using the hole saw drill 28mm hole from the outside using the pilot hole as a guide, deburr hole using a sharp knife or emery paper taking care not to mark outside of fairing. • Refit fairing (connect indicator push fittings). •...
- Page 7 FRANCE INSTRUCTIONS DE MONTAGE DES PROTECTIONS CP0281 HONDA CBR 125R 2011 Page | 7 ARRIERE DE LA MOTO AVANT DE LA MOTO R&G ’ ’ A PRESENTATION DES PIECES DANS L EMBALLAGE N EST PAS TOUJOURS IDENTIQUE AU SENS DE MONTAGE Merci de noter que dans le cas où...
- Page 8 Page | 8 Outil de marquage Gauche (assis sur la moto) • Enlevez le carénage latéral. • Enlevez les deux vis de cadre montrées en photo « D ». (utilisez la clef de 14mm). • Collez une bande de mousse sur le bloc en aluminium R&G. Cela afin d’éviter les griffes sur le cadre.
- Page 9 • Remontez le carénage sur la moto (connectez les clignotants). • Glissez une rondelle M10 sur l’une des vis M10x100 mm. • Glissez ensuite une rondelle M10 crantée contre la rondelle lisse. • Puis glissez le tout dans le tampon R&G. la tête de la vis et les rondelles seront positionnées dans le renfoncement du tampon de protection.