Submenu For Setting The Clock & Daily Event Timers (See Command 02); Access To The Submenus - FAS International FASTER ICE Mode D'emploi

FASTER ICE – Issue 00
SUBMENU FOR SETTING THE CLOCK & DAILY EVENT TIMERS (SEE COMMAND 02)
Alarm set 01
Alarm set 02
Alarm set 03
Alarm set 10
Alarm set 11
Alarm set 21
Alarm set 31
Alarm set 36
Alarm set 41
Alarm set 46
Alarm set 51
9.1.1

ACCESS TO THE SUBMENUS

Command 01 Machine test:
This is used to perform the test relative to the various selections. By keying in 01 followed by key B, the
message "Selection nr.
motors) and press B. The machine will check the selections that are effectively present (Test 12). If the
number found does not correspond to the value set, the message " CONFIG ERROR" appears on the
display. This indicates that one or more of the selections is not connected electrically. In this case, check the
wiring. If however the number of the selections found corresponds to the value set, 3 vending cycles for each
selection are performed. If during this phase, an anomaly in the function of a selection is encountered, the
test is blocked and the corresponding selection code remains visualised on the display. If the test is
performed successfully, the machine returns to the main programming menu (command 00).
Command 02 Calls submenu for setting the clock & daily timers:
Key in 02 and press the ENTER pushbutton to enter the submenu for setting the clock and daily timers.
Alarm 00 will appear on the display. Follow the method described in the specific section to display and alter
the parameters.
Command 03 Recall of price setting submenu (you see also Command 69):
Enter 03 and press ENTER to recall the submenu for price setting of each selection , and 'Selection
number 0' appears on the display.
Enter the number of the selection for which you wish to display or edit the price and press ENTER. The text
'Price......' appears on the display, then enter the new price value and press ENTER once again to memorise
it, or press the ESC key to return to the main menu without saving the changes.
To set the price of selection 6 at € 1.20 proceed as follows:

Programming mode, Command 0 appears on the display.

Type 03 and press ENTER, Selection number 0 appears on the display

Type 6 and press ENTER, the current price of Price No. appears on the display.

Set the value 120 and press ENTER.
Alternatively, prices can be programmed by drawer: selection 91 implies that all the selections in the first
drawer from the top have the same set price. Selection 92 = 2
th th
5 drawer; 96 = 6 drawer; 97 = 7
selections in the vending machine will be converted to the same set price.
Programming the value of the full prices changes the value of the corresponding discounted prices by making
them the same. Consequently, when selling with different prices, that is with a discount, firstly program the full
price then the discounted prices and never vice versa or only one of the two.
N.B.: With SPIRALI SLAVE connection enabled (see command 49), once the settings for the MASTER
machine have been completed, access is gained to the setting mode for the same parameters relevant to the
SLAVE machine by simply pressing the ESC button.
FAS INTERNATIONAL S.p.A. Via Lago di Vico, 60 SCHIO (VI) – tel. +39 0445 502011 – fax +39 0445 502010 - e-mail: info@fas.it
Sets the year/month/day
Sets the hour and minute
Setting the days of the week
Lighting control setting
Lights on/off
Setting the discount time slots
Selections disabled for daily time periods
Setting the selections with timed disabling
Product expiry time setting
Product expiry time selection setting
Weekly control of daily disabling of sales point
00" appears. Set the number of the selections present in the machine (number of
th
drawer. If you program a price in selection 99, the prices for all the
nd rd
drawer; 93 = 3 drawer; 94 = 4
17
E
N
G
L
I
S
H
th
drawer; 95 =