Important Safety Instructions - Makita 6207D Manuel D'instructions

ENGLISH
1 Battery cartridge
2 Button
3 Switch trigger
4 Reversing switch lever
5 Clockwise
6 Counterclockwise
7 Speed change lever
SPECIFICATIONS
Model
Capacities
Steel .................................................................. 10 mm
Wood ................................................................. 25.4 mm
Wood screw....................................................... 6 x 75 mm
Machine screw .................................................. 13 mm
-1
No load speed (min )
High ................................................................... 0 – 1,400
Low.................................................................... 0 – 450
Overall length ......................................................... 233 mm
Net weight .............................................................. 1.8 kg
Rated voltage ......................................................... D.C.9.6 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for drilling and screw driving in wood,
metal and plastic.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
CORDLESS DRILL SAFETY WARNINGS
1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
4
Explanation of general view
8 Action mode change lever
9 Lock button
10 Adjusting ring
11 Graduations
12 Pointer
13 Sleeve
14 Ring
6207D
8.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
GEA010-1
to safety rules for the subject product.
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE
GEB051-2
1.
2.
3.
4.
5.
6.
15 Bit
16 Bit holder
17 Limit mark
18 Brush holder cap
19 Screwdriver
6317D 6337D
13 mm 13 mm
25.4 mm 32 mm
6 x 75 mm 6 x 75 mm
13 mm 13 mm
0 – 1,400 0 – 1,400
0 – 450 0 – 450
241 mm 241 mm
2.0 kg 2.1 kg
D.C.12 V D.C.14.4 V
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
Do not disassemble battery cartridge.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
6347D
13 mm
38 mm
10 x 89 mm
13 mm
0 – 1,600
0 – 500
241 mm
2.3 kg
D.C.18 V
MISUSE or
ENC004-2