Bosch GAS 35 L AFC Professional Notice Originale page 19

Fitting the vacuuming accessories (see figure C)
The vacuum hose (21) is equipped with a clip system which
can be used to connect vacuuming accessories (dust extrac-
tion adapter (20), curved nozzle (22)).
Fitting the nozzles and tubes
– Push the curved nozzle (22) onto the vacuum hose (21)
until you hear both snap fasteners (31) on the vacuum
hose engage.
– Then attach the required extraction accessory (floor
nozzle, crevice nozzle, suction tube, etc.) firmly to the
curved nozzle (22).
– To remove the accessory, press the snap fasteners (31)
inwards and pull apart the components.
Fitting the dust extraction adapter
– Push the dust extraction adapter (20) onto the vacuum
hose (21) until you hear both snap fasteners (31) on the
vacuum hose engage.
– To remove the adapter, press the snap fasteners (31) in-
wards and pull apart the components.
Inserting/removing the disposal bag or dust bag
(dry extraction) (see figures D1–D2)
For dry vacuuming, you can insert a disposal bag (23) or a
dust bag (accessory) into the container (1). This makes the
dust easier to dispose of.
Note: If using a paper filter bag, you must make sure that
automatic filter cleaning (AFC) is switched off; you should
also do the same if using a fleece filter bag .
Inserting the disposal bag
– Open the catches (11) and remove the top part of the va-
cuum cleaner (10).
– Insert the disposal bag (23) into the container (1) with
the inlet facing forwards.
– Pull the inlet over the connection flange and all the way
into the recess of the connection flange.
– Make sure that the disposal bag (23) touches all the in-
side walls of the container (1).
– Fold the rest of the disposal bag (23) over the edge of the
container (1).
– Put the top part of the vacuum cleaner (10) on and close
the catches (11).
Removing and sealing the disposal bag
– Open the catches (11) and remove the top part of the va-
cuum cleaner (10).
– Pull the full disposal bag (23) backwards out of the con-
nection flange.
– Carefully take the disposal bag (23) out of the container
(1) without damaging it.
When doing so, make sure that the disposal bag does not
scrape against the connection flange or other sharp ob-
jects.
– Remove the adhesive strip cover and tape up the disposal
bag.
Bosch Power Tools
Then tie up the disposal bag (23) below the inlet using
the adhesive strip cover that has been removed.
Changing/inserting the dust bag (accessory)
– Open the catches (11) and remove the top part of the va-
cuum cleaner (10).
– Pull the full dust bag backwards out of the connection
flange. Close the opening in the dust bag by turning down
the top. Take the closed dust bag out of the container (1).
– Place the new dust bag over the vacuum cleaner's con-
nection flange. Make sure that the entire length of the
dust bag touches the inside wall of the container (1).
– Put the top part of the vacuum cleaner (10) on and close
the catches (11).
Fitting the rubber lip (wet vacuuming) (see
figure E)
Note: The requirements for the degree of penetration (dust
class L) have only been verified for dry vacuuming.
– Use a suitable tool to lift the brush inserts (27) out of the
floor nozzle (28).
– Place the rubber lips (26) in the floor nozzle (28).
Note: The textured side of the rubber lips must be facing
outwards.
Attaching the L-Boxx (see figure F)
You can attach an L-Boxx to the top part of the dust extractor
for transporting the extractor and to provide space-saving
storage for extractor accessories and/or the power tool.
– Click the L-Boxx onto the adapters (9).
Do not use the dust extractor with an L-Boxx attached.
u
This will raise the dust extractor's centre of gravity. The
extractor may tip over. There is a risk of injury and dam-
age if you do this.
Do not carry the dust extractor by the carrying handle
u
of the attached L-Boxx. The dust extractor is too heavy
for the carrying handle of the L-Boxx. There is a risk of in-
jury and damage if you do this.
Operation
Pull the plug out of the socket before cleaning or per-
u
forming maintenance on the vacuum cleaner, making
tool adjustments, changing accessories or putting
away the vacuum cleaner. This safety measure prevents
the vacuum cleaner from being started accidentally.
When operating the dust extractor, ensure that the
castors (14) blocked with the castor brakes (13) to prevent
the dust extractor from rolling away unintentionally. Test the
correct functioning of the wheels (12) and castors (14) on
the relevant surface before operation.
Start-up
Pay attention to the mains voltage. The voltage of the
u
power source must correspond with the information on
the type plate of the dust extractor. Dust extractors
marked with 230 V can also be operated with 220 V.
English | 19
1 609 92A 73J | (12.11.2021)