Visualisation - hager HZI810 Mode D'emploi

oPeratIon

Visualisation

presentation
• this mode allows parameters to be displayed in-
dependently from mode / Autswitch position
( if programmed on input)
• No code required to access parameters visualisation
• Without any action during 5 seconds on the
keypad, the LCD displays voltage available on active
network. In case of changeover switch on 0 position,
priority network voltage is displayed.
Navigation in visualisation mode:
• Press "up" and "bottom" push buttons to access required parameter
• Press "left" and "right" push buttons to navigate in the different menus
58
All manuals and user guides at all-guides.com
oPeratIon
Visualisation
visualisation architecture mode
Menu
Metering timers
Phase-neutral voltage V1 Main Failure timer
1 2
1 2 network 1 2
1 2
1 2 1 2 1 2
1 2
Phase-neutral voltage V2 Delay on transfer timer
1 2
1 2 1 2
network
1 2 1 2
1 2 1 2
1 2
1 2
1 2 1 2
1 2
1 2
1 2 1 2
1 2
Phase-neutral voltage V3 O Main Failure timer
1 2
1 2 1 2
1 2
network
1 2
1 2 1 2
1 2 1 2 1 2
1 2
1 2
1 2
1 2
1 2
1 2 1 2
1 2
1 2 1 2
frequency
1 2 1 2 Network Main Return timer
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2 1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2 1 2
1 2
1 2 Phase-phase u12 1 2 O Main Return timer
1 2
1 2
1 2
1 2
1 2 1 2
network
1 2 1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2 1 2
1 2
1 2
1 2
1 2 1 2
1 2
1 2
Phase-phase u23 Cool Down timer
1 2
1 2
1 2
1 2 1 2
1 2
network
1 2 1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2 Phase-phase u31 Load shedding*
1 2
1 2
1 2
1 2
1 2
1 2
1 2 network
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2 1 2
1 2
1 2 Phase-neutral V1
1 2
1 2
1 2
1 2
1 2
network
1 2
1 2 1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
Phase-phase u31
1 2
1 2
1 2
network
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2 frequency
Network
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
* If selected.
1 2
1 2
1 2
1 2
1 2
all values indicated might not be available according to programmed network. refer to annexes.
59
Counter
Priority source ➡
Emergency source
transfer counter