Connecting To Various Devices; Signals That Can Be Input To The Projector - JVC D-ILA DLA-G150CLU Manuel D'instructions

DLA-G150CLU&CLE_Eng.book Page 22 Thursday, February 21, 2002 2:39 PM

Connecting to Various Devices

Before connection, be sure to turn off the projector and connected devices.
Read the manual which comes with each device thoroughly.

Signals that Can Be Input to the Projector

The following signals can be input to the projector:
I Video signals
(1) Response to color systems
Color systems
Input terminal
VIDEO
Y/C
Y, P /B-Y, P /R-Y
B R
G, B, R, H/C , V
S
*1:Responds if Y/C output is available.
*2:Signifies that component signals ("Y, P
(synchronization and video period) of each color system. The color systems are used for convenience only.
(2)
Response to double density (*3), high-vision signals
Input terminal
Y, P /B-Y, P /R-Y
B R
G, B, R, H/C , V
S
*3:Signals whose density of scanning lines/field is twice as high.
*4:Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line
doubler (separately available: recommended article). Also, possible to respond to fully-specified, decoded
wide-clear-vision signal and decoded 525P progressive signal.
*5:Responds to signals whose horizontal scanning frequency is 33.5 kHz. PAL can be made twice as dense by a line doubler
(separately available: recommended article).
(3) Response to DTV-format signals
DTV-format signals (480i, 480p, 720p, 1080i) can be input to the Y, P
I Computer signals
Signals with the following scanning frequencies can be input to the PC 1 or PC 2 (G, B, R, H/C
Horizontal scanning frequency
Vertical scanning frequency
Be sure that the computer to be used suffices the following conditions:
• The computer has the video signal output port.
Be sure that the computer has the video signal output port by reading the instruction book of the computer.
The video signal output port is generally called as "RGB port", "monitor port", or "video port". If the computer-monitor hybrid
type or note type is used, it may need to prepare for an external output port. Also, there will be the type to which an external
output port cannot be installed.
• DVI input
During DVI input, depending on the computer settings, there may be no signal input or an error may occur (blue screen).
If this happens, turn off the power to both the projector and the computer, and then turn the projector back on before turning
the computer on again. Then correctly set the computer's graphic board.
• The resolution and the scanning frequencies are within the range specified in the table on page 23.
Be sure that the resolution and the scanning frequencies of the video signal are within the range. A video signal out of range
cannot be used. (Even signals out of the range could be projected. However, it may not sharp enough. On the other hand,
even some of the signals within the range may require adjustment depending on the video board used.)
When a signal other than listed in the table on page 23 is input, the image could be partially erased or an unneeded fold-over
image could appear.
Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.
Composite sync (C ) and G on Sync signals cannot be handled depending on the devices connected.
S
22
NTSC NTSC4.43
‡ ‡
‡
‡*
1
‡* ‡*
2 2
‡* ‡*
2 2
, P " / "Y, B-Y, R-Y" / "G, B, R, H/C
B R
4
NTSC*
‡
‡
15kHz - 105kHz
50Hz - 100Hz
DLA-G150CLU / LCT1123-001B / ENGLISH
PAL
‡
‡
‡*
2
‡*
2
, V") conform to the signal timing
S
5
High-vision signal
NTSC*
‡ ‡
‡ ‡
/B-Y, P /R-Y, G, B, R, H/C , V input terminal.
B R S
, V) and DVI terminals.
S
SECAM
‡
- - - - -
‡*
2
‡*
2