Environment Protection; Connecting The Machine - Electrical Connections; Noise Information; Earthing Instructions - PEUGEOT ENERGYSAW-254A Manuel D'utilisation

The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-of-life.
This applies to your device but also to any accessories marked with this symbol. do not dispose of these products as unsorted municipal waste.
In accordance with the WEEE directive concerning the environment, it is forbidden to abandon used electric or electronic equipment or leave them
at a standard public dump. The equipment must be taken to a collection point for treatment, recovery and recycling of EEE waste, or returned to its
dealer on a 1 for 1 basis (one item of equipment bought for one item of equipment taken back). The user is therefore taking an environmentally-frien-
dly step and helping to preserve natural resources and protect human health.
EXTENSION CORDS
Only use extension cords with three conductors ending in two-pin plugs and sockets with two holes and an earth pin that are suited to the plug of
the tool. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that
the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat.
Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacketed extension listed by laborato-
ries should be used.
Length of extension cord: up to 15 m
Wire size: 3 x 2.5 mm2
Before using an extension cord, inspect it for loose or exposed wires and cut or worn insulation. Repair or replace any damaged or worn cord imme-
diately.
ELECTRICAL CONNECTIONS
Your machine has a precision built electric motor. It should be connected to a power supply that is 230 V, 50 Hz. If your tool does not operate when
plugged into a socket, double-check the power supply characteristics.
The noise level of the machine is measured according to standards DIN EN ISO 3744: 1995-11 and DIN EN ISO 11203: 1996-07. The values given are
emission values calculated according to applicable standards and not values relating to use in the workplace. Although correlation between those
different emission levels does exist, this cannot be reliably used to determine whether additional precautions are necessary. Factors with potential
influence on the sound emission level in the workplace include the length of the period of work, the size of the room and any other sources of
noise (e.g. number of machines operating, other noisy work being carried out at the same time). Acceptable exposure levels may vary from one
country to another. For all these reasons, we would advise users to wear equipment to protect their ears while using this machine.
Maximum sound pressure level: 96,3 dB (A)
Maximum sound power level: 109,3 dB (A)
Uncertainties equal: 3 dB
Do not use a tool if its power cord is damaged. This tool is designed to be used with a circuit containing a power socket. It is also equipped with an
earthing pin.
16
All manuals and user guides at all-guides.com

EnVIROnMEnt PROtEctIOn

cOnnEctIng thE MAchInE – ElEctRIcAl cOnnEctIOnS

nOISE InfORMAtIOn

EARthIng InStRuctIOnS

Earthing consists in connecting metal masses, that are liable to come accidentally in
contact with the current due to faulty insulation in an electrical device, to an earth
connection by means of a conductive wire. That earth connection, when used with a dif-
ferential circuit breaker, prevents electrical incidents. The current flows directly into the
earth and the power supply is automatically cut off. Do not modify the supplied plug. If
it cannot be put into the socket, have an appropriate socket installed by a qualified elec-
trician. If the earth conductor of a machine is incorrectly connected, this can lead to a risk
of electric shock. The earth conductor is contained in green insulation with a yellow line.
If the power cord needs to be repaired or replaced, do not connect the earth conductor to
a live terminal.
Call in a qualified electrician or maintenance personnel if the earthing instructions
are not fully understood or if in any doubt about the correct earthing of the tool. If the
power supply cable is damaged, it should be replaced by the manufacturer, the manufac-
turer's after-sales department or similarly qualified person in order to avoid any danger.