GE GSM2200N15BB Manuel Du Propriétaire page 14

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Before you call for service...
Problem
Possible Causes
Dishes don't dry
Low inlet water
temperature
Rinse agent dispenser
is empty
Dishes and flatware
Inlet water temperature • Raise the water heater temperature to 49°C.
not clean
is below 49°C.
Too little detergent
Old or damp powdered • See Using the dishwasher section, refer to Proper Use of Detergent for
detergent
Water pressure is
temporarily low
Air gap is clogged
Improper rack loading
No air gap or high
drain loop
Spots and filming
Extremely hard water
on glasses and
Low inlet water
flatware
temperature
Overloading the
dishwasher
Improper loading
Old or damp powder
detergent
Rinse agent dispenser
empty
Too little detergent
Cloudiness on
Combination of soft
glassware
water and too much
detergent
Water temperature
entering the dishwasher
exceeds 65°C.
Detergent cup lid
Dial is not in the OFF
won't latch
position
Detergent left in
Dishes are blocking the • Reposition the dishes.
dispenser cups
detergent cups
Steam
This is normal
Black or gray
Aluminum utensils have • Remove marks with a mild, abrasive cleaner.
marks on dishes
rubbed against dishes
Control panel lights
Time too long between • Each pad must be touched within 30 seconds of the others. To relight,
go off when you are
touching or selecting
setting controls
pads
Control panel
Door latch may not
responded to inputs
be properly seated
but dishwasher never
filled with water
14
What To Do
• Make sure inlet water temperature is at least 49°C.
• Select HEATED DRY.
• Use HOT START and ADDED HEAT options.
• Select a higher cycle, such as POTS & PANS or HEAVY WASH.
• Check the rinse agent dispenser and fill as required.
• Use HOT START, POTS & PANS or HEAVY WASH and HI TEMP WASH.
• See Using the dishwasher section, refer to Proper Use of Detergent for
detergent recommendations.
detergent recommendations.
• Turn on a faucet. Is water coming out more slowly than usual? If so,
wait until pressure is normal before using your dishwasher.
• Clean the air gap.
• Make sure large dishware does not block detergent dispenser or wash arm.
• Verify that you have an air gap or a high drain loop. Refer to
the Installation Instructions.
• Use Jet-Dry
®
or Cascade Crystal Clear
and prevent new film buildup.
• To remove stubborn spots and pre-existing film from glassware:
1 Remove all metal utensils from the dishwasher.
2 Do not add detergent.
3 Select the longest cycle.
4 Start the dishwasher and allow to run for 18 to 22 minutes.
Dishwasher will now be in the main wash.
5 Open the door and pour 2 cups (500 ml) of white vinegar into the
bottom of the dishwasher.
6 Close the door and allow to complete the cycle. If vinegar rinse
doesn't work: Repeat as above, except use 1/4 cup (60 ml) of citric
acid crystals instead of vinegar.
• This is called etching and is permanent. To prevent this from
happening, use less detergent if you have soft water. Wash glassware in
the shortest cycle that will get them clean.
• Lower the water heater temperature.
• Turn the Timer Dial to OFF.
• Steam comes through the vent by the door latch during drying and
when water is being pumped out.
touch any pad again or unlatch and relatch the door.
• Call for service.
®
rinse agents to remove spots

Publicité

Table des Matières
loading

Table des Matières