Ryobi RTS10 Manuel D'utilisation page 5

 WHEN MAKING NON-THROUGH RIP CUTS, always
use a push stick, push block, and/or featherboard so your
hands do not come within 3 inches of the saw blade.
 WHEN RIPPING NARROW STOCK, always use a push
stick, push block, jig ( designed for narrow ripping), or
featherboard.
 NEVER perform any operation "freehand" which means
using only your hands to support or guide the workpiece.
Always use either the rip fence or miter fence to position
and guide the work.
 NEVER stand or have any part of your body in line with
the path of the saw blade.
 NEVER reach behind, over, or within three inches of the
blade or cutter with either hand for any reason.
 ALWAYS REMOVE THE RIP FENCE from the saw when
cross cutting.
 DO NOT USE THE MITER GAUGE AND RIP FENCE
during the same operation.
 NEVER use rip fence as cutoff gauge when cross cutting.
 NEVER attempt to free a stalled saw blade without first
turning the saw OFF and disconnecting the saw from the
power source.
 PROVIDE ADEQUATE SUPPORT to the rear and sides
of the saw table for wide or long work pieces.
 AVOID KICKBACKS (work thrown back toward you) by:
a) Keeping blade sharp.
b) Keeping rip fence parallel to the saw blade.
c) Keeping riving knife, anti-kickback pawls, and blade
guard in place and operating.
d) Not releasing the work before it is pushed all the way
past the saw blade using a push stick.
e) Not ripping work that is twisted or warped or does
not have a straight edge to guide along the fence.
CALIFORNIA PROPOSITION 65
WARNING:
This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities may
contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive
harm. Wash hands after handling.
Some examples of these chemicals are
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products and,
• arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your
exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially
designed to filter out microscopic particles.
All manuals and user guides at all-guides.com
SPECIFIC SAFETY RULES
5 - English
 IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
 AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause your hand
to move into the cutting tool.
 USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are not
listed may cause the risk of personal injury. Instructions for
safe use of accessories are included with the accessory.
 MAKE SURE THE WORK AREA HAS AMPLE LIGHTING
to see the work and that no obstructions will interfere with
safe operation BEFORE performing any work using the
table saw.
 ALWAYS TURN OFF SAW before disconnecting it, to
avoid accidental starting when reconnecting to power
supply.
 ONLY USE BLADES within the thickness range stamped
on the riving knife.
 THIS TOOL should have the following markings:
a) Wear eye protection.
b) Use saw blade guard and riving knife for every operation
for which it can be used, including all through sawing.
c) Keep hands out of the line of saw blade.
d) Use a push stick when required.
e) Pay particular attention to instructions on reducing
risk of kickback.
f) Do not perform any operation freehand.
g) Never reach around or over the saw blade.
h) Never operate saw on floor or below waist height.
 NEVER CUT MORE THAN ONE PIECE OF MATERIAL
AT A TIME.
 SAVE THESE INSTRUCTIONS. Refer to them frequently
and use to instruct other users. If you loan someone this
tool, loan them these instructions also.