Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
EnGLIsH
the dual range gear shifter is either completely pushed forward
or completely pushed back.
Pivoting LED Worklight (Fig. A, E)
CAUTION: Do not stare into worklight. Serious eye
injury could result.
The worklight
located on the foot of the tool is activated
5
when the trigger switch is depressed and is adjustable via three
detent positions. The off
17
can be changed by moving the worklight switch
of tool. In the on setting, the worklight will stay illuminated for
up to 20 seconds. If the trigger switch remains depressed, the
worklight will remain on.
nOTE: The worklight is for lighting the immediate work surface
and are not intended to be used as a flashlight.
Spotlight Mode
The spotlight will run for 20 minutes after the trigger switch is
released. Two minutes before the spotlight will shut off, it will
flash twice and then dim. To avoid the spotlight shutting off,
lightly tap the trigger switch.
WARNING: While using the worklight in medium or
spotlight mode, do not stare at the light or place the
drill in a position which may cause anyone to stare
into the light. Serious eye injury could result.
CAUTION: When using the tool as a spotlight, be sure
it is secured on a stable surface where it will not cause a
tripping or falling hazard.
CAUTION: Remove all accessories from the chuck before
using the drill as a spotlight. Personal injury or property
damage could result.
Low Battery Warning
When in spotlight mode and the battery is nearing complete
discharge, the spotlight will flash twice and then dim. After two
minutes, the battery will be completely discharged and the
drill will immediately shut down. At this point, replace with a
fresh battery.
WARNING: To reduce the risk of injury, always have a
back-up battery or secondary lighting available if the
situation warrants it.
Keyless Single Sleeve Chuck (Fig. C)
WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and remove the battery from the tool when
changing acces sories.
WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool causing possible
personal injury.
Your tool features a keyless chuck
sleeve
7
for one‑handed operation of the chuck. To insert a drill
bit or other accessory, follow these steps.
1. Turn tool off and remove the battery pack.
36
, on
18
, and spotlight
19
13
on the foot
with one rotating chuck
6
2. Grasp the black sleeve of the chuck with one hand and
use the other hand to secure the tool. Rotate the sleeve
anticlockwise (as viewed from the front) far enough to
accept the desired accessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise
with one hand while holding the tool with the other hand.
Continue to rotate the chuck sleeve until several ratchet
modes
clicks are heard to ensure full gripping power.
nOTE: Be sure to tighten chuck with one hand on
the chuck sleeve and one hand holding the tool for
maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
and one hand on the battery pack.
Drill Operation (Fig. A, D)
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood
"back-up" block to prevent damage to the material.
1. Turn the collar
2. Select the desired speed/torque range using the
gear shifter
planned operation.
3. For Wood, use twist bits, spade bits, power auger bits or
hole saws. For Metal, use high‑speed steel twist drill bits
or hole saws. Use a cutting lubricant when drilling metals.
The exceptions are cast iron and brass which should be
drilled dry.
4. Always apply pressure in a straight line with the bit. Use
enough pressure to keep drill biting, but do not push hard
enough to stall the motor or deflect the bit.
5. Hold tool firmly with both hands to control the twisting
action of the drill. If model is not equipped with side handle,
grip drill with one hand on the handle and one hand on the
battery pack.
3
to the drill symbol.
4
to match the speed and torque to the
16
Publicité
Table des Matières
