EINHELL GC-CC 18 Li Instructions D'origine page 19

screw again.
5.4. Installing the battery (Fig. 9/10)
Press the side pushlock button of the battery
pack as shown in Fig. 9 and push the battery
pack into the mount provided. When the battery
is positioned as in Fig. 10, make sure that the
pushlock button latches in place! To remove the
battery pack, proceed in reverse order.
5.5 Charging the battery (Fig. 11)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(14) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (13) into the battery
charger (14).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Anl_GC_CC_18_Li_SPK7.indb 19 Anl_GC_CC_18_Li_SPK7.indb 19
GB
5.6 Battery capacity indicator (Fig. 11b)
Press the switch for the battery capacity indicator
(Fig. 11b/Item A). The battery capacity indicator
(Fig. 11b/Item B) shows the charge status of the
battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
To obtain maximum performance from your pa-
ving scraper, please follow the instructions given
below:
•
Never use the paving scraper without the gu-
ard.
•
To switch on your paving scraper press the
safety lock-off (Fig. 2/Item 1) and then press
the On/Off switch (Fig. 2/Item 2).
•
To switch off your paving scraper, let go of the
On/Off switch again (Fig. 2/Item 2).
One steel brush (Fig. 2/Item 9) and one nylon
brush (Fig 2/Item 8) are supplied with the equip-
ment. The wire brush is suited for use on robust
surfaces and obstinate weeds. We recommend
using the nylon brush for light vegetation and sur-
faces too sensitive for the steel brush.
Important! Always carry out a short trial run
to check out possible eff ects on the surfaces
of the paving stones or slabs before starting
with your work. Never use the equipment on
very sensitive surfaces, for example tiles.
Important! Only use brushes which are in
fl awless condition. Replace excessively worn
or damaged brushes immediately.
- 19 -
06.09.2021 09:10:02 06.09.2021 09:10:02