Festo CMMP-AS Serie Manuel D'instructions page 8

8 Technical data
General
CMMP-AS- C2-3A-M0
Dimensions and weight
Dimensions [mm] 202x66x207
1)
(HxWxD)
Mounting plate [mm] 248x61
dimensions
Weight [kg] 2.1
Certifications
CE marking (see declaration In accordance with EU Low Voltage Directive
of conformity)
In accordance with EU EMC Directive
In accordance with EU Machinery Directive
1) Without plugs, shield screw and screw heads
Operating and environmental conditions
CMMP-AS- C2-3A-M0
General
Permissible setup altitude above sea level
with rated output [m] 1000
with power [m] 1000 ... 2000 (max.)
1)
reduction
Air humidity [%] 0 ... 90 (non-condensing)
Protection class IP20 (with plugged-in plug connectors at X6 and X9)
IP10 (without plugged-in plug connectors at X6 and X9)
Degree of contamination 2
Transport and storage
Temperature range [°C] -25 ... +70
Operation
Operating temperature [°C] 0 ... +40
Operating temperature [°C] +40 ... +50
with power reduction
of 2.5 % per Kelvin
Switch-off °C 100
temperature, heat
sink power section
1) Above 1000 m above sea level Performance reduction of 1% per 100 m
Power supply [X9]
CMMP-AS- C2-3A-M0
Logic supply
Nominal voltage [V DC] 24 ±20 %
1)
Nominal current [A] 0.55
Maximum current [A] 1
2)
for holding brake
Load supply
Number of phases 1
Nominal voltage [V AC] 100 ... 230
Nominal voltage [%] ±10 %
tolerance
Mains frequency [Hz] 50 ... 60
Alternative DC [V DC] 60 ... 380
power feed
1) plus current consumption of a holding brake and I/Os, if present
2) for higher power requirements è Hardware description
I/O interface [X1]
Type
Digital inputs/outputs
Inputs Input voltage
DIN0 ... DIN9
Voltage range
Outputs Output voltage
DOUT 0 ... DOUT3
1)
Voltage range
+24 V Output voltage
Max. output current
GND24 Voltage
With use as digital input (configuration with FCT)
1)
C5-3A-M0 C5-11A-P3-M0 C10-11A-P3-M0
227x66x207 252x79x247
297x75
2.2 3.5
C5-3A-M0 C5-11A-P3-M0 C10-11A-P3-M0
80 80 80
C5-3A-M0 C5-11A-P3-M0 C10-11A-P3-M0
0.65 1
2
3
230 ... 480
±10 %
60 ... 700
Values Comment
[V] 24 Active high,
conforming to
[V] 8 ... 30
EN 61131-2
[V] 24 Active high,
galvanically
[V] 8 ... 30
separated
[V] 24
[mA] 100
[V] 0 Reference
potential for
digital I/Os
I/O interface [X1]
Type
Analogue inputs/outputs
AIN0 Input section
#AINO
Resolution
Time delay
Max. input voltage
R
I
AIN11) Input section
Resolution
Time delay
AIN21) Input section
Resolution
Time delay
AMON0, AMON1 Output section
Resolution
Critical frequency
AGND Voltage
+VREF Output section
This input can also be optionally parameterised as a digital input with an 8 V switching
1)
threshold (parameterisation with FCT).
Supported encoders [X2A]/[X2B]
Encoder type Protocol
Resolver –
Digital encoders Incremental
Analogue encoders –
EnDat encoders EnDat 2.1 (01/21); EnDat 2.2 (22)
HIPERFACE encoders HIPERFACE
Details è Hardware description
Motor connection [X6]
1)
CMMP-AS- C2-3A-M0
Voltage [V 0 ... 270
AC]
Nominal power [kVA] 0.5
Max. power for [kVA] 1
5 seconds
1) Data for operation with 1x230 V AC [± 10%], 50 ... 60 Hz
2) Data for operation at 3x400 V AC [±10 %], 50 Hz
è All available technical data è Hardware description.
Values Comment
[V] ±10 differential –
Bit 16
 250
[μs]
[V] 30
[kΩ] 30
[V] ±10 Single-ended –
Bit 10
 250
[μs]
[V] ±10 Single-ended –
[Bit] 10
 250
[μs]
[V] ±10 –
[Bit] 9
[kHz] 1
[V] 0 Reference potential
[V] 0 ... 10 Reference output
for setpoint
potentiometer
Interface
[X2A]
[X2B]
[X2B]
[X2B]
[X2B]
1) 2)
C5-3A-M0 C5-11A-P3-M0 C10-11A-P3-M0
0 ... 360
1 3 6
2 6 12
2)