Software Update - Bosch SmartphoneHub Manuel Du Propriétaire

Inserting a smartphone into the universal holder
(see figures A and B)
A universal holder (16) is supplied for attaching a smart-
phone. Specific holders for iPhones can be purchased from
the range of accessories. No separate power supply is ne-
cessary for an iPhone holder.
For the universal holder, the power (5 V/1 A, max. 1.5 A) is
supplied using a separate USB cable (included with delivery)
via the micro‑A/B USB port of the SmartphoneHub.
Inserting the univer- Push the universal holder (16) onto
sal holder
the SmartphoneHub from the front
(see figure A)
until you hear it click into place ➊. The
universal holder can also be fixed in
place using the two fastening
screws (17).
Inserting the smart- – Pull the front mounting
phone bracket (18) forwards ➋.
(see figure B)
– Insert the smartphone with the long
side of the phone positioned
against the rear mounting
bracket (19) ➌.
– Allow the front mounting
bracket (18) to slide slowly to-
wards the smartphone and release
it ➍.
Power supply for The smartphone can be supplied with
the smartphone power (5 V/1 A) using a separate USB
(optional) cable (included with delivery) via the
micro-A/B USB port of the Smart-
phoneHub. To do this, connect the
smartphone to the USB port of the
SmartphoneHub using the USB cable.
Removing the Use both hands to push the smart-
smartphone phone forwards along with the front
mounting bracket until the smart-
phone can be removed from the uni-
versal holder. If necessary, remove
the USB cable for the power supply.

Software update

If a software update is available for the SmartphoneHub, an
indicator is shown in the smartphone app. Follow the in-
structions in the app to perform the update.
Recovering the SmartphoneHub
A recovery operation should be carried out on the Smart-
phoneHub if it is no longer functioning correctly. To do this,
open the app on your smartphone and follow the instruc-
tions.
Power supply for the SmartphoneHub
The SmartphoneHub has an internal lithium-ion polymer bat-
tery (nominal/minimum 300 mAh, 3.7 V) that cannot be re-
moved.
The SmartphoneHub can be switched on via its on/off but-
ton (2) or via the on/off button of the eBike battery. If the
Bosch eBike Systems
SmartphoneHub cannot be switched on, it must be charged
via a USB cable for at least 30 minutes.
If you do not use your SmartphoneHub, recharge the Smart-
phoneHub every three months. You can charge the Smart-
phoneHub battery via its USB port with any power adaptor,
smartphone charger, etc.
Switching the push assistance on/off
The push assistance aids you when pushing your eBike. The
speed in this function depends on the selected gear and can
reach a maximum of 6 km/h. The lower the selected gear,
the lower the speed of the push assistance function (at full
power).
The push assistance function must only be used when
u
pushing the eBike. There is a risk of injury if the wheels
of the eBike are not in contact with the ground while using
the push assistance.
To activate the push assistance, briefly press the WALK
button on your operating unit. Once it is activated, press and
hold the + button within three seconds. The eBike drive is
now switched on.
Note: The push assistance cannot be activated at assistance
level OFF.
The push assistance is switched off as soon as one of the
following occurs:
– You release the + button;
– The wheels of the eBike are locked (e.g. by applying the
brakes or hitting an obstacle);
– The speed exceeds 6 km/h.
The push assistance function is subject to local regulations;
the way it works may therefore differ from the description
above, or the function may even be deactivated completely.
Setting the assistance level
On the operating unit (15), you can set the level of assist-
ance you want the eBike drive to provide you with while ped-
alling. The assistance level can be changed at any time, even
while cycling.
Note: In some models, the assistance level may be preset
and cannot be changed. There may also be fewer assistance
levels available than stated here.
The following assistance levels are available as a maximum:
– OFF: Motor assistance is switched off. The eBike can just
be moved by pedalling, as with a normal bicycle. The
push assistance cannot be activated at this assistance
level.
– ECO: Effective assistance with maximum efficiency, for
maximum range
– TOUR: Steady assistance, long range for touring
21
English – 3
1 270 020 XBC | (22.04.2020)