Residual Risks; Technical Data - Scheppach SM150LB Traduction Des Instructions D'origine

• Only true the grinding disc on the front side. Grind-
ing on the side surfaces can make the grinding disc
too thin for safe use.
• Grinding generates heat. Do not touch the work-
piece until it has cooled down sufficiently.
• Only use grinding discs that are designed for safe
use on the bench grinder. Do not use a grinding disc
whose specified maximum rotational speed is lower
than the speed specification of the device.
• Do not use any damaged or deformed grinding
wheels or brushes.
• Only use grinding wheels and brushes marked with
a rotational speed which is at least as high as the
speed indicated on the rating plate of the electrical
tool.
• Always leave the brush fastened to the spindle in
order to limit the risk of contact with the rotating
spindle.
Safety instructions for handling batteries
1. Always make sure that the batteries are inserted
with the correct polarity (+ and –), as indicated on
the battery.
2. Do not short-circuit batteries.
3. Do not charge non-rechargeable batteries.
4. Do not overcharge batteries!
5. Do not mix old and new batteries or batteries of dif-
ferent types or manufacturers! Replace an entire
set of batteries at the same time.
6. Immediately remove used batteries from the de-
vice and dispose of them properly!
7. Do not allow batteries to heat up!
8. Do not weld or solder directly on batteries!
9. Do not dismantle batteries!
10. Do not allow batteries to deform!
11. Do not throw batteries into fire!
12. Keep batteries out of the reach of children.
13. Do not allow children to replace batteries without
supervision!
14. Do not keep batteries near fire, ovens or other
sources of heat. Do not use batteries in direct sun-
light or store them in vehicles in hot weather.
15. Keep unused batteries in the original packaging
and keep them away from metal objects. Do not
mix unpacked batteries or toss them together! This
can lead to a short-circuit of the battery and thus
damage, burns or even the risk of fire.
16. Remove batteries from the equipment when it will
not be used for an extended period of time, unless
it is for emergencies!
24 | GB
17. NEVER handle batteries that have leaked without
appropriate protection. If the leaked fluid comes
into contact with your skin, the skin in this area
should be rinsed off under running water imme-
diately. Always prevent the fluid from coming into
contact with the eyes and mouth. In the event of
contact, please seek immediate medical attention.
18. Clean the battery contacts and corresponding
contacts in the device prior to inserting the bat-
teries.

6. Residual risks

The machine has been built according to the state-of-
the-art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the "Safety infor-
mation" and the "Proper use" together with the oper-
ating manual as a whole are observed.
• Avoid accidental starting of the machine: the op-
erating button may not be pressed when inserting
the plug in an outlet. Use the tool attachment that
is recommended in this operating manual. This is
how to ensure that your machine provides optimum
performance.
• Keep your hands away from the work area, when the
machine is in operation.
7.

Technical data

Motor
Rated input
Idle speed
Dimensions
Max. disc Ø
Min. disc Ø (after wear)
Max. brush Ø
Min. brush Ø (after wear)
Disc hole
Disc width
www.scheppach.com
230 - 240 V~ / 50 Hz
S1:250 W
S2 10 min:400 W
2980 min
-1
380 x 210 x 280 mm
Ø 150 mm
Ø 110 mm
Ø 150 mm
Ø 120 mm
Ø 12.7 mm
20 mm