DeWalt DCW682 Traduction De La Notice D'instructions Originale page 40

EngLIsh
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Paddle switch
1
Lock‑off switch
2
Auxiliary handle
3
Fence height adjuster
4
Dust extraction outlet
5
Adjustable fence
6
Anti‑slipping pins
7
Plunge depth adjusting knob
8
Fence height locking knob
9
Spindle lock
10
Adjustable fence locking knob
11
Battery
12
Battery release
13
Intended Use
Your biscut jointer has been designed for making flat dowel
joints in wood and wood products.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
The biscut jointer is a professional power tool.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOtE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
38
WALT battery packs and chargers.
e
12 is fully charged.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 14 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOtE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Adjustable Fence (Fig. D1, D2)
The adjustable fence 6 allows you to precisely set the point
where the slots for the biscuits are cut. To set the fence height:
1. Slacken the fence height locking knob
2. Set the height adjuster
90 °, the scale under the locking knob reads the distance
between the centre of cutter and the surface of the fence.
3. Tighten the locking knob.
To Set the Fence Angle
1. Slacken the adjustable fence locking knob
2. Tilt the fence into the required angle.
3. Tighten the adjustable fence locking knob.
The fine adjustment is used to eliminate possible tolerances in
the size of the biscuit slots.
Jointer Base Markings
When working without the fence, for example when making
T‑joints, you can use the grooves on the jointer base for proper
alignment of the tool.
1. Set the fence to the 0 ° position as described above.
2. For workpieces with a thickness of 19 mm, use the edge of
the base as a reference for centring.
3. For other workpieces, use the red centreline marking to
align the tool.
4. Two of the grooves indicate the length of the cut. In order to
prevent breaking through the workpiece, make sure that the
workpiece extends beyond these grooves.
Plunge Depth Adjustment (Fig. E)
The plunge depth must be set to match the biscuit size. The
numbers 0, 10 and 20 on the depth adjusting knob correspond
with the biscuit size. The M represents the maximum cutting
depth of approx. 20 mm.
nOtE: The maximum cutting depth of 20 mm is obtainable
only with a new blade and by backing out the fine adjustment
screw (refer to Plunge Depth Fine Adjustment).
13 and firmly pull the
9 .
4 as required. With the fence set to
11 .