Gaggenau CV492100 Notice D'utilisation page 20

Securing the adapter
Hold the adapter at the central holder and use the
1.
side holders to slide it towards the unit's back
panel in the base unit, then affix it.
→ Fig.
41
If required, also use screws to secure it.
2.
→ Fig.
42
Installing the appliance for air recirculation mode
with circulating-air duct
For circulating-air mode, use the seal, the circulat-
1.
ing-air duct, the diffuser and the odour filter.
Observe the dimensions for the different flat duct
2.
bends. → Page 16
Securing the seal
Secure the seal on the flat duct elbow at a max-
▶
imum of 5 mm from the edge.
→ Fig.
43
Inserting the flat duct elbow
Insert the flat duct elbow into the outlet opening
▶
on the rear of the appliance.
→ Fig.
44
Inserting the appliance into the worktop cut-out
Carefully insert the appliance into the worktop cut-
▶
out.
→ Fig.
45
Establishing the pipework between the
appliance and the diffuser
Connect the components of the circulating-air duct
1.
to each other.
→ Fig.
46
Connect the circulating-air duct to the flat duct el-
2.
bow on the rear of the hob.
→ Fig.
47
Connect the diffuser to the circulating-air duct.
3.
→ Fig.
48
Screwing the retaining clips in place
Screw the enclosed retaining clips onto the work-
▶
top and carefully onto the appliance.
Ensure that the hob is at the same height as the
‒
worktop and the appliance does not slip.
Do not use an electric screwdriver.
‒
→ Fig.
40
Install the appliance for air extraction mode
For air extraction mode, use the seal and the
1.
acoustics filters.
Observe the instructions for the exhaust air pipe.
2.
→ Page 18
Securing the seal
Secure the seal on the flat duct elbow at a max-
▶
imum of 5 mm from the edge.
→ Fig.
43
Establishing the piping
Insert the flat duct elbow into the outlet opening
1.
on the rear of the appliance.
→ Fig.
44
If required, install additional piping elements.
2.
Inserting the appliance into the worktop cut-out
Carefully insert the appliance into the worktop cut-
▶
out.
→ Fig.
45
20
Screwing the retaining clips in place
Screw the enclosed retaining clips onto the work-
▶
top and carefully onto the appliance.
Ensure that the hob is at the same height as the
‒
worktop and the appliance does not slip.
Do not use an electric screwdriver.
‒
→ Fig.
40
Connecting the exhaust air pipe
Secure the exhaust air pipe to the flat duct bend.
1.
Establish the connection to the exhaust air open-
2.
ing.
Seal the joints appropriately.
3.
Connecting the cables to the appliance
Connect one of the longer cables to the appliance
1.
and to any control knob.
→ Fig.
49
Ensure that the plugs snap into place in the sock-
2.
ets.
Inserting filters
Note: For circulating-air mode, insert the odour fil-
ters.
For air extraction mode, insert the acoustics filters.
Observe the filters' air flow direction.
1.
Insert two of the filters into the left and right of the
2.
appliance, and slide them forwards.
→ Fig.
50
Insert the other filters into the left and right of the
3.
appliance.
→ Fig.
51
Inserting grease filters
Insert the grease filter.
▶
→ Fig.
52
Positioning the ventilation grille
Position the ventilation grille.
▶
→ Fig.
53
Establishing the connection to the power
supply
Observe the connection data on the rating plate.
1.
For 3 N, connect the cable to the mains socket in
2.
accordance with the figure.
→ Fig.
54
For 2 N, connect the cable to the mains socket in
3.
accordance with the figure.
→ Fig.
55
For 1 N, connect the cable to the mains socket in
4.
accordance with the figure.
→ Fig.
56
For 2 L/2 N, connect the cable to the mains
5.
socket in accordance with the figure.
→ Fig.
57
Note the colours of the cables.
6.
– BN: Brown
– BU: Blue
– GN/YE: Yellow and green
– BK: Black
– GY: Grey
If required, arrange the supplied wire end ferrules
7.
differently depending on the type of connection.
To connect two cables, if required, use a wire end
8.
ferrule.
Shorten the wires.
‒
Remove the insulation.
‒
Checking the function
Switch on the appliance.
1.