Gaggenau CV492100 Notice D'utilisation page 19

Provide a minimum air outlet cross-section of
‒
approx. 440 cm².
To keep the draught and noise low, ensure that
‒
the outlet opening in the base panel is as large
as possible.
To guarantee that the appliance works correctly,
4.
ventilate the hob appropriately via an air outlet
with a minimum cross-section of 200 cm² in the
base unit.
After making the cut-outs, remove any shavings.
5.
Seal the cut surfaces so that they are heat-resist-
6.
ant and waterproof.
→ Fig.
24
Preparing the unit for circulating-air mode with a
circulating-air duct
If required, remove the unit's back wall.
1.
Observe the relevant dimensions when combining
2.
with the AD 857 030 flat duct elbow for the cut-
out in the back wall.
→ Fig.
27
In circulating-air mode, establish an air outlet in
3.
the unit's plinth.
Provide a minimum air outlet cross-section of
‒
approx. 440 cm².
To keep the draught and noise low, ensure that
‒
the outlet opening in the base panel is as large
as possible.
To guarantee that the appliance works correctly,
4.
ventilate the hob appropriately via an air outlet
with a minimum cross-section of 200 cm² in the
base unit.
After making the cut-outs, remove any shavings.
5.
Seal the cut surfaces so that they are heat-resist-
6.
ant and waterproof.
→ Fig.
24
Preparing the unit for air extraction mode
If required, remove the unit's back wall.
1.
Observe the relevant dimensions when combining
2.
with a flat duct elbow for the cut-out in the back
wall.
→ Fig.
28
After making the cut-outs, remove any shavings.
3.
Seal the cut surfaces so that they are heat-resist-
4.
ant and waterproof.
→ Fig.
24
Attaching adhesive tape
Attach the enclosed adhesive tape to the worktop
▶
section.
→ Fig.
29
Installing the control knob
Break the retaining plate into four pieces at the
1.
perforation.
→ Fig.
30
Remove the protective film from the rear of the il-
2.
luminated ring.
→ Fig.
31
Hold the retaining plate in place against the rear
3.
of the control panel.
Push the control knob into the hole.
4.
Ensure that the retaining lug on the retaining plate
5.
is located at the top and the control knob is in the
zero setting.
→ Fig.
32
On the rear of the control knob, tighten the nut us-
6.
ing the installation aid provided.
→ Fig.
33
Align the control knob precisely in the zero setting.
7.
Use two screws to secure the retaining plate
8.
against rotation.
→ Fig.
34
In the case of stone worktops, stick the retaining
9.
plate using temperature-resistant two-component
adhesive.
Connecting the control knob with cables
Use the enclosed cables to connect all of the con-
1.
trol knobs.
→ Fig.
35
The two cable connectors on the control knob are
identical.
Ensure that the plugs snap into place in the con-
2.
nectors.
Connect the central control knobs to one of the
3.
longer cables.
After installation, check that all of the plug connec-
4.
tions are seated correctly.
Bend the lug on the retaining plate in order to se-
5.
cure all of the cables following installation.
→ Fig.
36
Installing the appliance
WARNING ‒ Risk of injury!
Parts that are accessible during installation may
have sharp edges and may lead to cutting injuries.
Wear protective gloves
▶
The appliance is heavy.
To move the appliance, two people are required.
▶
Use only suitable tools and equipment.
▶
Install the appliance for air extraction mode
▶
→ Page 20, circulating-air mode → Page 19 or
circulating-air mode with circulating-air duct
→ Page 20.
Note: The appliance is only intended for flush install-
ation.
Installing the appliance for circulating-air mode
with adapter
Note: When installing directly on a non-insulated
outer wall (µ ≥ 0.5 W/m² °C), we recommend a con-
figuration with circulating-air duct.
For the circulating-air mode, use the adapter and
1.
the odour filter.
Ensure that the clearance between the appliance
2.
and the rear panel of the unit is between 10 and
80 mm.
Attaching the adapter
Clean and degrease the adhesive surface around
1.
the cut-out in the unit's back panel.
Insert the adapter into the outlet opening on the
2.
rear of the hob.
→ Fig.
37
Remove the adhesive tape's protective film from
3.
the adapter.
→ Fig.
38
Inserting the appliance into the worktop cut-out
Carefully insert the appliance into the worktop cut-
▶
out.
→ Fig.
39
Screwing the retaining clips in place
Screw the enclosed retaining clips onto the work-
▶
top and carefully onto the appliance.
Ensure that the hob is at the same height as the
‒
worktop and the appliance does not slip.
Do not use an electric screwdriver.
‒
→ Fig.
40
19